IBM HC10 User Guide - Page 34

Completing, installation, Installing, blade, workstation, bezel, assembly

Get IBM HC10 - BladeCenter - 7996 PDF manuals and user guides
UPC - 883436017671
View all IBM HC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Completing the installation To complete the installation, complete the following tasks. Instructions for each task are in the following sections. 1. Reinstall the blade workstation bezel assembly, if you removed it (see "Installing the blade workstation bezel assembly" for information on installing the bezel assembly). 2. Close the blade workstation cover (see "Closing the blade workstation cover" on page 23). Statement 21: CAUTION: Hazardous energy is present when the blade is connected to the power source. Always replace the blade cover before installing the blade. 3. Reinstall the blade workstation into the BladeCenter unit (see "Installing the blade workstation in a BladeCenter unit" on page 24). 4. Turn on the blade workstation (see "Turning on the blade workstation" on page 11). 5. For certain optional devices, run the blade workstation Configuration/Setup Utility program (see "Updating the blade workstation configuration" on page 25). Note: If you have just connected the power cords of the BladeCenter unit to electrical outlets, you must wait until the power-on LED on the blade workstation flashes slowly before you press the power-control button. Installing the blade workstation bezel assembly The following illustration shows how to install the bezel assembly. Bezel-assembly release Bezel-assembly release Bezel Control-panel cable Control-panel connector To install the blade workstation bezel assembly, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 15. 2. Connect the control-panel cable to the control-panel connector on the system board. 3. Carefully slide the bezel assembly onto the blade workstation until it clicks into place. 22 BladeCenter HC10 Type 7996: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Completing
the
installation
To
complete
the
installation,
complete
the
following
tasks.
Instructions
for
each
task
are
in
the
following
sections.
1.
Reinstall
the
blade
workstation
bezel
assembly,
if
you
removed
it
(see
“Installing
the
blade
workstation
bezel
assembly”
for
information
on
installing
the
bezel
assembly).
2.
Close
the
blade
workstation
cover
(see
“Closing
the
blade
workstation
cover”
on
page
23).
Statement
21:
CAUTION:
Hazardous
energy
is
present
when
the
blade
is
connected
to
the
power
source.
Always
replace
the
blade
cover
before
installing
the
blade.
3.
Reinstall
the
blade
workstation
into
the
BladeCenter
unit
(see
“Installing
the
blade
workstation
in
a
BladeCenter
unit”
on
page
24).
4.
Turn
on
the
blade
workstation
(see
“Turning
on
the
blade
workstation”
on
page
11).
5.
For
certain
optional
devices,
run
the
blade
workstation
Configuration/Setup
Utility
program
(see
“Updating
the
blade
workstation
configuration”
on
page
25).
Note:
If
you
have
just
connected
the
power
cords
of
the
BladeCenter
unit
to
electrical
outlets,
you
must
wait
until
the
power-on
LED
on
the
blade
workstation
flashes
slowly
before
you
press
the
power-control
button.
Installing
the
blade
workstation
bezel
assembly
The
following
illustration
shows
how
to
install
the
bezel
assembly.
Control-panel connector
Control-panel cable
Bezel-assembly
release
Bezel-assembly
release
Bezel
To
install
the
blade
workstation
bezel
assembly,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
15.
2.
Connect
the
control-panel
cable
to
the
control-panel
connector
on
the
system
board.
3.
Carefully
slide
the
bezel
assembly
onto
the
blade
workstation
until
it
clicks
into
place.
22
BladeCenter
HC10
Type
7996:
Installation
and
User’s
Guide