IBM HC10 User Guide - Page 53

Using

Get IBM HC10 - BladeCenter - 7996 PDF manuals and user guides
UPC - 883436017671
View all IBM HC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Using SOL Note: Do not use Planar Ethernet for PXE/DHCP booting or installation. When this network interface attempts to boot through PXE or DHCP, the network interface is reset, causing the current SOL session to be dropped and have a new status of Not Ready. f. Select Startup Options; then, set Planar Ethernet PXE/DHCP to Disabled. g. Press Esc to exit the Startup Options section of the Configuration/Setup Utility program. h. Select Save Settings; then, press Enter. i. Press Enter to confirm. j. Select Exit Setup; then, press Enter. k. Make sure that Yes, exit the Setup Utility is selected; then, press Enter. Follow the instructions in the BladeCenter Serial over LAN Setup Guide to start an SOL session, end an SOL session, monitor an SOL session, and restart a blade workstation through SOL. The following table contains the escape-key sequences to use during a blade workstation SOL session, when using the VT100 terminal emulation mode (the default). Note: There is a time limit for entering an escape-key sequence. If an escape-key sequence does not appear to work, it might be because the time limit for entering the key sequence has expired. Keyboard key Ctrl+Shift+F1 Ctrl+Shift+F2 Ctrl+Shift+F3 Ctrl+Shift+F4 Ctrl+Shift+F5 Ctrl+Shift+F6 Ctrl+Shift+F7 Ctrl+Shift+F8 Ctrl+Shift+F9 Ctrl+Shift+F10 Ctrl+Shift+F11 Ctrl+Shift+F12 Delete Down arrow End F1 F2 F3 F4 F5 Escape-key sequence Esc [ 6 4 ~ Esc [ 6 5 ~ Esc [ 6 6 ~ Esc [ 6 7 ~ Esc [ 6 8 ~ Esc [ 6 9 ~ Esc [ 7 0 ~ Esc [ 7 1 ~ Esc [ 7 2 ~ Esc [ 7 3 ~ Esc [ 7 4 ~ Esc [ 7 5 ~ Esc Esc [ B Esc k Esc 1 Esc 2 Esc 3 Esc 4 Esc 5 Chapter 5. Setting up Serial over LAN for the HC10 blade workstation 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Note:
Do
not
use
Planar
Ethernet
for
PXE/DHCP
booting
or
installation.
When
this
network
interface
attempts
to
boot
through
PXE
or
DHCP,
the
network
interface
is
reset,
causing
the
current
SOL
session
to
be
dropped
and
have
a
new
status
of
Not
Ready.
f.
Select
Startup
Options
;
then,
set
Planar
Ethernet
PXE/DHCP
to
Disabled
.
g.
Press
Esc
to
exit
the
Startup
Options
section
of
the
Configuration/Setup
Utility
program.
h.
Select
Save
Settings
;
then,
press
Enter.
i.
Press
Enter
to
confirm.
j.
Select
Exit
Setup
;
then,
press
Enter.
k.
Make
sure
that
Yes,
exit
the
Setup
Utility
is
selected;
then,
press
Enter.
Using
SOL
Follow
the
instructions
in
the
BladeCenter
Serial
over
LAN
Setup
Guide
to
start
an
SOL
session,
end
an
SOL
session,
monitor
an
SOL
session,
and
restart
a
blade
workstation
through
SOL.
The
following
table
contains
the
escape-key
sequences
to
use
during
a
blade
workstation
SOL
session,
when
using
the
VT100
terminal
emulation
mode
(the
default).
Note:
There
is
a
time
limit
for
entering
an
escape-key
sequence.
If
an
escape-key
sequence
does
not
appear
to
work,
it
might
be
because
the
time
limit
for
entering
the
key
sequence
has
expired.
Keyboard
key
Escape-key
sequence
Ctrl+Shift+F1
Esc
[
6
4
~
Ctrl+Shift+F2
Esc
[
6
5
~
Ctrl+Shift+F3
Esc
[
6
6
~
Ctrl+Shift+F4
Esc
[
6
7
~
Ctrl+Shift+F5
Esc
[
6
8
~
Ctrl+Shift+F6
Esc
[
6
9
~
Ctrl+Shift+F7
Esc
[
7
0
~
Ctrl+Shift+F8
Esc
[
7
1
~
Ctrl+Shift+F9
Esc
[
7
2
~
Ctrl+Shift+F10
Esc
[
7
3
~
Ctrl+Shift+F11
Esc
[
7
4
~
Ctrl+Shift+F12
Esc
[
7
5
~
Delete
Esc
-
Down
arrow
Esc
[
B
End
Esc
k
F1
Esc
1
F2
Esc
2
F3
Esc
3
F4
Esc
4
F5
Esc
5
Chapter
5.
Setting
up
Serial
over
LAN
for
the
HC10
blade
workstation
41