IBM IC35L040AVER07 Reference Manual - Page 47

Appendix - 40 jumper settings

Get IBM IC35L040AVER07 - Deskstar 40 GB Hard Drive PDF manuals and user guides View all IBM IC35L040AVER07 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Appendix Record your IBM Deskstar drive information here: Serial number Part number Model number Cylinders Heads Sectors Capacity Cables 40-pin, 40-conductor ATA/IDE cables This cable type will support up to and including ATA/33 (UDMA mode 2). Cables cannot be in excess of 18 inches and are limited to the attachment of 2 ATA devices plus the system board connector. The jumper settings designate a Master or Slave drive, not the position of the drive on the cable. 40-pin, 80-conductor ATA/IDE cables This cable type is constructed using the Cable Select configuration. It will support Ultra ATA/100 and Ultra ATA/66 interface transfer rates and is backward compatible. The extra 40 conductors are grounded shields to improve signal quality and reduce cross talk. The connectors of the 80conductor cable are color-coded. The black connector specifies Master drive connection, gray specifies Slave drive connection, and blue specifies connection to the ATA/IDE port of the motherboard or controller card. Jumpers Master If the IBM Deskstar is the only drive on the cable or the Master drive on a two-drive cable, set the jumpers for Master. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
43
Appendix
Record your IBM Deskstar drive information here:
Serial number
Part number
Model number
Cylinders
Heads
Sectors
Capacity
Cables
40-pin, 40-conductor ATA/IDE cables
This cable type will support up to and including ATA/33 (UDMA mode 2).
Cables cannot be in
excess of 18 inches and are limited to the attachment of 2 ATA devices plus the system board
connector.
The jumper settings designate a Master or Slave drive, not the position of the drive on
the cable.
40-pin, 80-conductor ATA/IDE cables
This cable type is constructed using the Cable Select configuration.
It will support Ultra ATA/100
and Ultra ATA/66 interface transfer rates and is backward compatible.
The extra 40 conductors
are grounded shields to improve signal quality and reduce cross talk.
The connectors of the 80-
conductor cable are color-coded.
The black connector specifies Master drive connection, gray
specifies Slave drive connection, and blue specifies connection to the ATA/IDE port of the
motherboard or controller card.
Jumpers
Master
If the IBM Deskstar is the only drive on the cable or the Master drive on a two-drive cable, set the
jumpers for Master.