Image Fitness 5.2 English Manual - Page 27

Adjust, Image®

Get Image Fitness 5.2 PDF manuals and user guides View all Image Fitness 5.2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

HOW TO ADJUST THE IMAGE® 5.2 The instructions below describe how each part of the IMAGE 5.2 can be adjusted. Refer to the exercise guide accompanying this manual to see how the IMAGE 5.2 should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the correct starting position for the exercise to be performed. If there is any slack in the cables or chain as an exercise is performed, the effectiveness of the exercise will be reduced. CHANGING THE WEIGHT SETTING To change the weight setting of either weight stack, insert a Weight Pin (100) under the desired Weight (75). Be sure to insert the Weight Pin until the bent end of the Weight Pin is touching the Weights, and turn the bent end downward. The weight setting of either weight stack can be changed from 10 pounds to 200 pounds, in increments of 10 pounds. Note: Due to the cables and pulleys, the amount of resistance at each exercise station may vary from the weight setting. Refer to the accompanying WEIGHT RESISTANCE CHART to find the approximate amount of resistance at each weight station. ATTACHING THE ROW BAR OR NYLON STRAP TO THE LOW PULLEY STATION Note: Before you use the low pulley station, the leg lever must be locked (see LOCKING THE LEG LEVER on page 28). Attach the Row Bar (93) to the Curl Cable (106) with a Cable Clip (102). For some exercises, the Chain (101) should be attached between the Row Bar and the Curl Cable with two Cable Clips. Adjust the length of the Chain between the Row Bar and the Curl Cable so the Row Bar is In the correct starting position for the exercise to be performed. The Nylon Strap (103) can be attached in the same manner. 0 100 75 0 a 106 101 103 SE 102 93 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
HOW
TO
ADJUST
THE
IMAGE®
5.2
The
instructions
below
describe
how
each
part
of
the
IMAGE
5.2
can
be
adjusted.
Refer
to
the
exercise
guide
accompanying
this
manual
to
see
how
the
IMAGE
5.2
should
be
set
up
for
each
exercise.
IMPORTANT:
When
attaching
the
lat
bar
or
nylon
strap,
make
sure
that
the
attachments
are
in
the
correct
starting
position
for
the
exercise
to
be
performed.
If
there
is
any
slack
in
the
cables
or
chain
as
an
exercise
is
performed,
the
effectiveness
of
the
exercise
will
be
reduced.
CHANGING
THE
WEIGHT
SETTING
To
change
the
weight
setting
of
either
weight
stack,
insert
a
Weight
Pin
(100)
under
the
desired
Weight
(75).
Be
sure
to
insert
the
Weight
Pin
until
the
bent
end
of
the
Weight
Pin
is
touching
the
Weights,
and
turn
the
bent
end
downward.
The
weight
setting
of
either
weight
stack
can
be
changed
from
10
pounds
to
200
pounds,
in
increments
of
10
pounds.
Note:
Due
to
the
cables
and
pulleys,
the
amount
of
resistance
at
each
exercise
station
may
vary
from
the
weight
setting.
Refer
to
the
accompany-
ing
WEIGHT
RESISTANCE
CHART
to
find
the
approximate
amount
of
resistance
at
each
weight
station.
ATTACHING
THE
ROW
BAR
OR
NYLON
STRAP
TO
THE
LOW
PULLEY
STATION
Note:
Before
you
use
the
low
pulley
station,
the
leg
lever
must
be
locked
(see
LOCKING
THE
LEG
LEVER
on
page
28).
Attach
the
Row
Bar
(93)
to
the
Curl
Cable
(106)
with
a
Cable
Clip
(102).
For
some
exercises,
the
Chain
(101)
should
be
attached
between
the
Row
Bar
and
the
Curl
Cable
with
two
Cable
Clips.
Adjust
the
length
of
the
Chain
between
the
Row
Bar
and
the
Curl
Cable
so
the
Row
Bar
is
In
the
correct
start-
ing
position
for
the
exercise
to
be
performed.
The
Nylon
Strap
(103)
can
be
attached
in
the
same
manner.
0
100
75
0
a
106
101
103
102
93
SE
27