Intel S1200RP Technical Product Specification - Page 26

Power Subsystem

Intel

®

Server System R1000RP Family TPS

Intel

order number: G91532-003

Revision 1.2

16

dielectric strength criteria. If the working voltage between primary and secondary dictates a

higher dielectric strength test voltage, the highest test voltage should be used. In addition, the

insulation system must comply with reinforced insulation as per safety standard IEC 950.

Separation between the primary and secondary circuits, and primary to ground circuits, must

comply with the IEC 950 spacing requirements.

3.1.4.4

AC Line Dropout/Holdup

An AC line dropout is defined when the AC input drops to 0VAC at any phase angle of the

nominal AC line voltage. An AC line dropout less than 12ms shall not cause any tripping of

control signals or protection circuits for 350W output. If the AC line dropout over 12ms, the

power supply should recover back to normal operation and meet all turn on requirements. Any

dropout of the AC line shall not cause damage to the power supply.

3.1.4.5

AC Line Fuse

The power supply should have one line fused in the single line fuse on the line (Hot) wire of the

AC input. The line fusing must be acceptable for all safety agency requirements. The input fuse

should be a slow blow type. AC inrush current must not cause the AC line fuse to blow under

any conditions. All protection circuits in the power supply should not cause the AC fuse to blow

unless a component in the power supply has failed. This includes DC output load short

conditions.

3.1.4.6

AC Inrush

The peak inrush current must not damage the PSU, or the input fuse must not blow under any

conditions of load, temperature, and input voltage, including repeated, rapid cycling of the power

line. Half cycle peak inrush current, peak repetitive input current, and worse case power factor

must be provided by the vendor to assist with the UPS and line conditioning, sizing, and

selection. No component will be stressed over its maximum specification. This must be

demonstrated through measurements of the critical component specifications.

The peak inrush

current shall be less than 55A peak at 115VAC input and 230VAC input, cold start and 25°C.

3.1.4.7

AC Line Leakage Current

The maximum leakage current to ground shall be less than 1.0mA-rms at 240Vac, 50Hz.

3.1.4.8

AC Line Transient Specification

The AC line transient conditions are defined as sag and surge conditions. Sag conditions are

also commonly referred to as “brownout”

. Sag conditions are defined as the conditions when the

AC line voltage drops below nominal voltage. Surge conditions are defined as the conditions

when the AC line voltage rises above nominal voltage.

The power supply must meet the requirements under the following AC line sag and surge

conditions.

Table 8. AC Line Sag Transient Performance

AC Line Sag (10sec interval between each sagging)

Duration

Sag

Operating AC Voltage

Line Frequency

Performance Criteria

Continuous

10%

Nominal AC Voltage ranges

50/60Hz

No loss of function or performance

Section	Page
1. Introduction	11
1.1 Chapter Outline	11
1.2 Server Board Use Disclaimer	11
2. Product Overview	12
2.1 System Views	14
2.2 System Dimensions	15
2.3 System Level Environmental Limits	15
2.4 System Features and Options Overview	17
2.4.1 Hot Swap Hard Drive Bay and Front Panel Options	17
2.4.2 Back Panel Features	18
2.4.3 Front Control Panel Options	18
2.5 Server Board Overview	19
2.5.1 Rear Component View	21
2.6 Available Front Bezel Support (Optional)	21
2.7 Available Rack and Cabinet Mounting Kit Options	22
3. Power Subsystem	23
3.1 350W Fixed Power Supply	23
3.1.1 Mechnical Overview	23
3.1.2 Power Supply Module Efficiency	24
3.1.3 Power Cord Specification Requirements	24
3.1.4 AC Input Requirement	25
3.1.4.1 Power Factor	25
3.1.4.2 AC Input Voltage Specification	25
3.1.4.3 AC Line Isolation Requirements	25
3.1.4.4 AC Line Dropout/Holdup	26
3.1.4.5 AC Line Fuse	26
3.1.4.6 AC Inrush	26
3.1.4.7 AC Line Leakage Current	26
3.1.4.8 AC Line Transient Specification	26
3.1.4.9 Susceptibility Requirements	27
3.1.4.10 Electrostatic Discharge Susceptibility	27
3.1.4.11 Fast Transient/Burst	27
3.1.4.12 Radiated Immunity	27
3.1.4.13 Surge Immunity	28
3.1.4.14 Power Recovery	28
3.1.4.15 Voltage Interruptions	28
3.1.5 DC Output Specification	28
3.1.5.1 Output Power/Currents	28
3.1.5.2 Standby Output	28
3.1.6 Protection Circuits	28
3.1.6.1 Over Current Protection (OCP)	29
3.1.6.2 Over Voltage Protection (OVP)	29
3.1.6.3 Over Temperature Protection (OTP)	29
3.2 450W mini-ERPS Redundant Power Supply	29
3.2.1 Mechnical Overview	30
3.2.2 Power Supply Module Card Edge Connector	31
3.2.3 Power Supply Module Efficiency	32
3.2.4 Power Cord Specification Requirements	32
3.2.5 AC Input Requirement	32
3.2.5.1 Power Factor	32
3.2.5.2 AC Input Voltage Specification	32
3.2.5.3 AC Line Isolation Requirements	33
3.2.5.4 AC Line Dropout/Holdup	33
3.2.5.5 AC Line Fuse	33
3.2.5.6 AC Inrush	34
3.2.5.7 AC Line Leakage Current	34
3.2.5.8 AC Line Transient Specification	34
3.2.5.9 Susceptibility Requirements	34
3.2.5.10 Electrostatic Discharge Susceptibility	35
3.2.5.11 Fast Transient/Burst	35
3.2.5.12 Radiated Immunity	35
3.2.5.13 Surge Immunity	35
3.2.5.14 Power Recovery	35
3.2.5.15 Voltage Interruptions	35
3.2.6 DC Output Specification	36
3.2.6.1 Output Power/Currents	36
3.2.6.2 Standby Output	36
3.2.7 Protection Circuits	36
3.2.7.1 Current Limit (OCP)	36
3.2.7.2 Over Voltage Protection (OVP)	37
3.2.7.3 Over Temperature Protection (OTP)	37
4 Thermal Management	38
4.1 Thermal Operation and Configuration Requirements	38
4.2 Thermal Management Overview	39
4.2.1 Set Throttling Mode	39
4.2.2 Altitude	40
4.2.3 Set Fan Profile	40
4.2.4 Fan PWM Offset	40
4.2.5 Quiet Fan Idle Mode	40
4.2.6 Thermal Sensor Input for Fan Speed Control	40
4.3 System Fans	42
4.4 FRUSDR Utility	44
5 System Storage and Peripheral Options	45
5.1 2.5” Hard Disk Drive Support	45
5.1.1 2.5” Drive Hot-Swap Backplane Overview	46
5.1.2 Cypress* CY8C22545 Enclosure Management Controller	47
5.2 3.5” Hard Disk Drive Support	47
5.2.1 3.5” Drive Hot-Swap Backplane Overview	48
5.2.2 Cypress* CY8C22545 Enclosure Management Controller	49
5.3 SATA DOM Support	49
6 Storage Controller Options Overview	50
6.1 Embedded SATA Controller Support	50
7 Front Control Panel and I/O Panel Overview	51
7.1 I/O Panel Features	51
7.2 Control Panel Features	51
8 Intel® Local Control Panel	56
8.1 LCD Functionality	56
8.2 Main Menu	57
8.3 Event Menu	58
8.4 View Menu	58
8.4.1 System FW Version (SysFwVer)	58
8.4.2 System Information (SysInfo)	59
8.4.3 BMC IP Configuration	59
8.4.4 RMM4 IP Configuration	59
8.4.5 Power	60
8.4.6 Last Post Code (Last PC)	60
8.5 Config Menu	60
8.5.1 IP Version	60
8.5.2 BMC IP	60
8.5.3 RMM4 IP	62
8.5.4 Boot Device	62
8.5.5 Banner	62
9 PCIe Support and Riser Card Support	64
9.1 Architectural Overview of the Server Board Riser Slots	64
Appendix A: Integration and Usage Tips	67
Appendix B: POST Code LED Decoder	68
Appendix C: POST Code Errors	73
Glossary	79

Intel S1200RP Technical Product Specification - Page 26

AC Line Dropout/Holdup, 1.4.5, AC Line Fuse, 1.4.6, AC Inrush, 1.4.7, AC Line Leakage Current

Page 26 highlights