Home » Intel Manuals » Servers » Intel S1200RP » Manual Viewer

Intel S1200RP Technical Product Specification - Page 45

System Storage and Peripheral Options

Get Intel S1200RP PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Intel® Server System R1000RP Family TPS System Storage and Peripheral Options 5 System Storage and Peripheral Options The Intel® Server System R1000RP product family has support for many storage device options, including:  Hot Swap 2.5" Hard Disk Drives  Hot Swap 3.5" Hard Disk Drives  SATA Optical Drive Support for different storage and peripheral device options will vary depending on the system SKU. This section provides an overview of each available option. 5.1 2.5" Hard Disk Drive Support The server is available with support for eight 2.5" hard disk drives as illustrated below. Figure 25. 2.5" Hard Drive Bay Drive Configuration The drive bay can support either SATA or SAS hard disk drives. Mixing of drive types within the hard drive bay is not supported. Hard disk drive type is dependent on the type of host bus controller used, SATA only or SAS. Each 2.5" hard disk drive is mounted to a drive carrier, allowing for hot swap extraction and insertion. Drive carriers have a latching mechanism that is used to extract and insert drives from the chassis, and lock the tray in place. Light pipes integrated into the drive tray assembly direct the light emitted from Amber drive status and Green activity LEDs located next to each drive connector on the backplane, to the drive tray faceplate, making them visible from the front of the system. Amber Status LED Green Activity LED Figure 26. LED of HDD Carrier Table 25. Drive Status LED States Amber Off Solid On Blink No access and no fault Hard Drive Fault has occured RAID rebuild in progress (1 Hz), Identify (2 Hz) Revision 1.2 Intel order number: G91532-003 35

Section	Page
1. Introduction	11
1.1 Chapter Outline	11
1.2 Server Board Use Disclaimer	11
2. Product Overview	12
2.1 System Views	14
2.2 System Dimensions	15
2.3 System Level Environmental Limits	15
2.4 System Features and Options Overview	17
2.4.1 Hot Swap Hard Drive Bay and Front Panel Options	17
2.4.2 Back Panel Features	18
2.4.3 Front Control Panel Options	18
2.5 Server Board Overview	19
2.5.1 Rear Component View	21
2.6 Available Front Bezel Support (Optional)	21
2.7 Available Rack and Cabinet Mounting Kit Options	22
3. Power Subsystem	23
3.1 350W Fixed Power Supply	23
3.1.1 Mechnical Overview	23
3.1.2 Power Supply Module Efficiency	24
3.1.3 Power Cord Specification Requirements	24
3.1.4 AC Input Requirement	25
3.1.4.1 Power Factor	25
3.1.4.2 AC Input Voltage Specification	25
3.1.4.3 AC Line Isolation Requirements	25
3.1.4.4 AC Line Dropout/Holdup	26
3.1.4.5 AC Line Fuse	26
3.1.4.6 AC Inrush	26
3.1.4.7 AC Line Leakage Current	26
3.1.4.8 AC Line Transient Specification	26
3.1.4.9 Susceptibility Requirements	27
3.1.4.10 Electrostatic Discharge Susceptibility	27
3.1.4.11 Fast Transient/Burst	27
3.1.4.12 Radiated Immunity	27
3.1.4.13 Surge Immunity	28
3.1.4.14 Power Recovery	28
3.1.4.15 Voltage Interruptions	28
3.1.5 DC Output Specification	28
3.1.5.1 Output Power/Currents	28
3.1.5.2 Standby Output	28
3.1.6 Protection Circuits	28
3.1.6.1 Over Current Protection (OCP)	29
3.1.6.2 Over Voltage Protection (OVP)	29
3.1.6.3 Over Temperature Protection (OTP)	29
3.2 450W mini-ERPS Redundant Power Supply	29
3.2.1 Mechnical Overview	30
3.2.2 Power Supply Module Card Edge Connector	31
3.2.3 Power Supply Module Efficiency	32
3.2.4 Power Cord Specification Requirements	32
3.2.5 AC Input Requirement	32
3.2.5.1 Power Factor	32
3.2.5.2 AC Input Voltage Specification	32
3.2.5.3 AC Line Isolation Requirements	33
3.2.5.4 AC Line Dropout/Holdup	33
3.2.5.5 AC Line Fuse	33
3.2.5.6 AC Inrush	34
3.2.5.7 AC Line Leakage Current	34
3.2.5.8 AC Line Transient Specification	34
3.2.5.9 Susceptibility Requirements	34
3.2.5.10 Electrostatic Discharge Susceptibility	35
3.2.5.11 Fast Transient/Burst	35
3.2.5.12 Radiated Immunity	35
3.2.5.13 Surge Immunity	35
3.2.5.14 Power Recovery	35
3.2.5.15 Voltage Interruptions	35
3.2.6 DC Output Specification	36
3.2.6.1 Output Power/Currents	36
3.2.6.2 Standby Output	36
3.2.7 Protection Circuits	36
3.2.7.1 Current Limit (OCP)	36
3.2.7.2 Over Voltage Protection (OVP)	37
3.2.7.3 Over Temperature Protection (OTP)	37
4 Thermal Management	38
4.1 Thermal Operation and Configuration Requirements	38
4.2 Thermal Management Overview	39
4.2.1 Set Throttling Mode	39
4.2.2 Altitude	40
4.2.3 Set Fan Profile	40
4.2.4 Fan PWM Offset	40
4.2.5 Quiet Fan Idle Mode	40
4.2.6 Thermal Sensor Input for Fan Speed Control	40
4.3 System Fans	42
4.4 FRUSDR Utility	44
5 System Storage and Peripheral Options	45
5.1 2.5” Hard Disk Drive Support	45
5.1.1 2.5” Drive Hot-Swap Backplane Overview	46
5.1.2 Cypress* CY8C22545 Enclosure Management Controller	47
5.2 3.5” Hard Disk Drive Support	47
5.2.1 3.5” Drive Hot-Swap Backplane Overview	48
5.2.2 Cypress* CY8C22545 Enclosure Management Controller	49
5.3 SATA DOM Support	49
6 Storage Controller Options Overview	50
6.1 Embedded SATA Controller Support	50
7 Front Control Panel and I/O Panel Overview	51
7.1 I/O Panel Features	51
7.2 Control Panel Features	51
8 Intel® Local Control Panel	56
8.1 LCD Functionality	56
8.2 Main Menu	57
8.3 Event Menu	58
8.4 View Menu	58
8.4.1 System FW Version (SysFwVer)	58
8.4.2 System Information (SysInfo)	59
8.4.3 BMC IP Configuration	59
8.4.4 RMM4 IP Configuration	59
8.4.5 Power	60
8.4.6 Last Post Code (Last PC)	60
8.5 Config Menu	60
8.5.1 IP Version	60
8.5.2 BMC IP	60
8.5.3 RMM4 IP	62
8.5.4 Boot Device	62
8.5.5 Banner	62
9 PCIe Support and Riser Card Support	64
9.1 Architectural Overview of the Server Board Riser Slots	64
Appendix A: Integration and Usage Tips	67
Appendix B: POST Code LED Decoder	68
Appendix C: POST Code Errors	73
Glossary	79