Home » Intel Manuals » Servers » Intel S1200RP » Manual Viewer

Intel S1200RP Technical Product Specification - Page 46

Swap Backplane Overview

Get Intel S1200RP PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

System Storage and Peripheral Options Intel® Server System R1000RP Family TPS Table 26. Drive Activity LED States Green Condition Power on with no drive activity Power on with drive activity Power on and drive spun down Power on and drive spinning up Drive Type SAS SATA SAS SATA SAS SATA SAS SATA LED stays on Behavior LED stays off LED blinks off when processing a command LED blinks on when processing a command LED stays off LED stays off LED blinks LED stays off 5.1.1 2.5" Drive Hot-Swap Backplane Overview Figure 27. The Front Side of 8 X 2.5" Hot Swap Backplane On the backside of each backplane are several connectors. The following illustration identifies each connector. Label A B C Description Power connector 4-port Mini-SAS cable connectors SMBus*-In cable connector - From Server board Figure 28. The Back Side of 8 X 2.5" Hot Swap Backplane A - Power Harness Connector: The backplane includes a 2x2 connector supplying power to the backplane. Power is routed to the backplane through a power cable harness from the server board. B - Multi-port Mini-SAS Cable Connectors: The backplane includes two multi-port mini-SAS cable connectors, each providing I/O signals for four SAS/SATA hard drives on the backplane. Cables can be routed from matching connectors on the server board, add-in SAS/SATA RAID cards, or optionally installed SAS expander cards. C - SMBus* Cable Connectors: The backplane includes a 1x5 cable connector used as a management interface to the server board. 36 Intel order number: G91532-003 Revision 1.2

Section	Page
1. Introduction	11
1.1 Chapter Outline	11
1.2 Server Board Use Disclaimer	11
2. Product Overview	12
2.1 System Views	14
2.2 System Dimensions	15
2.3 System Level Environmental Limits	15
2.4 System Features and Options Overview	17
2.4.1 Hot Swap Hard Drive Bay and Front Panel Options	17
2.4.2 Back Panel Features	18
2.4.3 Front Control Panel Options	18
2.5 Server Board Overview	19
2.5.1 Rear Component View	21
2.6 Available Front Bezel Support (Optional)	21
2.7 Available Rack and Cabinet Mounting Kit Options	22
3. Power Subsystem	23
3.1 350W Fixed Power Supply	23
3.1.1 Mechnical Overview	23
3.1.2 Power Supply Module Efficiency	24
3.1.3 Power Cord Specification Requirements	24
3.1.4 AC Input Requirement	25
3.1.4.1 Power Factor	25
3.1.4.2 AC Input Voltage Specification	25
3.1.4.3 AC Line Isolation Requirements	25
3.1.4.4 AC Line Dropout/Holdup	26
3.1.4.5 AC Line Fuse	26
3.1.4.6 AC Inrush	26
3.1.4.7 AC Line Leakage Current	26
3.1.4.8 AC Line Transient Specification	26
3.1.4.9 Susceptibility Requirements	27
3.1.4.10 Electrostatic Discharge Susceptibility	27
3.1.4.11 Fast Transient/Burst	27
3.1.4.12 Radiated Immunity	27
3.1.4.13 Surge Immunity	28
3.1.4.14 Power Recovery	28
3.1.4.15 Voltage Interruptions	28
3.1.5 DC Output Specification	28
3.1.5.1 Output Power/Currents	28
3.1.5.2 Standby Output	28
3.1.6 Protection Circuits	28
3.1.6.1 Over Current Protection (OCP)	29
3.1.6.2 Over Voltage Protection (OVP)	29
3.1.6.3 Over Temperature Protection (OTP)	29
3.2 450W mini-ERPS Redundant Power Supply	29
3.2.1 Mechnical Overview	30
3.2.2 Power Supply Module Card Edge Connector	31
3.2.3 Power Supply Module Efficiency	32
3.2.4 Power Cord Specification Requirements	32
3.2.5 AC Input Requirement	32
3.2.5.1 Power Factor	32
3.2.5.2 AC Input Voltage Specification	32
3.2.5.3 AC Line Isolation Requirements	33
3.2.5.4 AC Line Dropout/Holdup	33
3.2.5.5 AC Line Fuse	33
3.2.5.6 AC Inrush	34
3.2.5.7 AC Line Leakage Current	34
3.2.5.8 AC Line Transient Specification	34
3.2.5.9 Susceptibility Requirements	34
3.2.5.10 Electrostatic Discharge Susceptibility	35
3.2.5.11 Fast Transient/Burst	35
3.2.5.12 Radiated Immunity	35
3.2.5.13 Surge Immunity	35
3.2.5.14 Power Recovery	35
3.2.5.15 Voltage Interruptions	35
3.2.6 DC Output Specification	36
3.2.6.1 Output Power/Currents	36
3.2.6.2 Standby Output	36
3.2.7 Protection Circuits	36
3.2.7.1 Current Limit (OCP)	36
3.2.7.2 Over Voltage Protection (OVP)	37
3.2.7.3 Over Temperature Protection (OTP)	37
4 Thermal Management	38
4.1 Thermal Operation and Configuration Requirements	38
4.2 Thermal Management Overview	39
4.2.1 Set Throttling Mode	39
4.2.2 Altitude	40
4.2.3 Set Fan Profile	40
4.2.4 Fan PWM Offset	40
4.2.5 Quiet Fan Idle Mode	40
4.2.6 Thermal Sensor Input for Fan Speed Control	40
4.3 System Fans	42
4.4 FRUSDR Utility	44
5 System Storage and Peripheral Options	45
5.1 2.5” Hard Disk Drive Support	45
5.1.1 2.5” Drive Hot-Swap Backplane Overview	46
5.1.2 Cypress* CY8C22545 Enclosure Management Controller	47
5.2 3.5” Hard Disk Drive Support	47
5.2.1 3.5” Drive Hot-Swap Backplane Overview	48
5.2.2 Cypress* CY8C22545 Enclosure Management Controller	49
5.3 SATA DOM Support	49
6 Storage Controller Options Overview	50
6.1 Embedded SATA Controller Support	50
7 Front Control Panel and I/O Panel Overview	51
7.1 I/O Panel Features	51
7.2 Control Panel Features	51
8 Intel® Local Control Panel	56
8.1 LCD Functionality	56
8.2 Main Menu	57
8.3 Event Menu	58
8.4 View Menu	58
8.4.1 System FW Version (SysFwVer)	58
8.4.2 System Information (SysInfo)	59
8.4.3 BMC IP Configuration	59
8.4.4 RMM4 IP Configuration	59
8.4.5 Power	60
8.4.6 Last Post Code (Last PC)	60
8.5 Config Menu	60
8.5.1 IP Version	60
8.5.2 BMC IP	60
8.5.3 RMM4 IP	62
8.5.4 Boot Device	62
8.5.5 Banner	62
9 PCIe Support and Riser Card Support	64
9.1 Architectural Overview of the Server Board Riser Slots	64
Appendix A: Integration and Usage Tips	67
Appendix B: POST Code LED Decoder	68
Appendix C: POST Code Errors	73
Glossary	79