Home » Intel Manuals » Servers » Intel S1200RP » Manual Viewer

Intel S1200RP Technical Product Specification - Page 67

Appendix A: Integration and Usage Tips - s1200v3rp drivers

Get Intel S1200RP PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Appendix A: Integration and Usage Tips Intel® Server System R1000RP Family TPS Appendix A: Integration and Usage Tips Before attempting to integrate and configure your system, you should reference this section, which provides a list of useful information.  After the system is integrated with processors, memory, and peripheral devices, the FRUSDR utility must be run to load the proper Sensor Data Record data to the integrated Server Management subsystem. Failure to run this utility may prevent Server Management from accurately monitoring system health and may affect system performance. The FRUSDR utility for this server system can either be run from the Intel® Deployment CDROM that came with your system or can be downloaded from the Intel® website referenced at the bottom of this page.  To ensure the highest system reliability, make sure the latest system software is loaded on the server before deploying the system onto a live networking environment. This includes system BIOS, FRUSDR, BMC firmware, and hot-swap controller firmware. The system software can be updated using the Intel® Deployment DVD that came with your system or can be downloaded from the Intel® website referenced at the bottom of this page.  System fans are not hot-swappable.  Only supported memory validated by Intel should be used in this server system. A list of supported memory can be found in the Intel® Server Board S1200V3RP Tested Memory List which can be downloaded from the Intel® website referenced at the bottom of this page.  This system supports the Intel® Xeon® processor E3-1200 V3 series. You cannot use Intel® Xeon® processors not referenced on the supported processor list in this server system.  You must use the CPU/memory air duct to maintain system thermals.  To maintain system thermals, you must populate all hard drive bays with either a hard drive or drive blank.  You must remove AC power from the system prior to opening the chassis for service. You can download the latest system documentation, drivers, and system software from the Intel® Support website at http://www.intel.com/p/en_US/support/highlights/server/R1000RP. Revision 1.2 Intel order number: G91532-003 57

Section	Page
1. Introduction	11
1.1 Chapter Outline	11
1.2 Server Board Use Disclaimer	11
2. Product Overview	12
2.1 System Views	14
2.2 System Dimensions	15
2.3 System Level Environmental Limits	15
2.4 System Features and Options Overview	17
2.4.1 Hot Swap Hard Drive Bay and Front Panel Options	17
2.4.2 Back Panel Features	18
2.4.3 Front Control Panel Options	18
2.5 Server Board Overview	19
2.5.1 Rear Component View	21
2.6 Available Front Bezel Support (Optional)	21
2.7 Available Rack and Cabinet Mounting Kit Options	22
3. Power Subsystem	23
3.1 350W Fixed Power Supply	23
3.1.1 Mechnical Overview	23
3.1.2 Power Supply Module Efficiency	24
3.1.3 Power Cord Specification Requirements	24
3.1.4 AC Input Requirement	25
3.1.4.1 Power Factor	25
3.1.4.2 AC Input Voltage Specification	25
3.1.4.3 AC Line Isolation Requirements	25
3.1.4.4 AC Line Dropout/Holdup	26
3.1.4.5 AC Line Fuse	26
3.1.4.6 AC Inrush	26
3.1.4.7 AC Line Leakage Current	26
3.1.4.8 AC Line Transient Specification	26
3.1.4.9 Susceptibility Requirements	27
3.1.4.10 Electrostatic Discharge Susceptibility	27
3.1.4.11 Fast Transient/Burst	27
3.1.4.12 Radiated Immunity	27
3.1.4.13 Surge Immunity	28
3.1.4.14 Power Recovery	28
3.1.4.15 Voltage Interruptions	28
3.1.5 DC Output Specification	28
3.1.5.1 Output Power/Currents	28
3.1.5.2 Standby Output	28
3.1.6 Protection Circuits	28
3.1.6.1 Over Current Protection (OCP)	29
3.1.6.2 Over Voltage Protection (OVP)	29
3.1.6.3 Over Temperature Protection (OTP)	29
3.2 450W mini-ERPS Redundant Power Supply	29
3.2.1 Mechnical Overview	30
3.2.2 Power Supply Module Card Edge Connector	31
3.2.3 Power Supply Module Efficiency	32
3.2.4 Power Cord Specification Requirements	32
3.2.5 AC Input Requirement	32
3.2.5.1 Power Factor	32
3.2.5.2 AC Input Voltage Specification	32
3.2.5.3 AC Line Isolation Requirements	33
3.2.5.4 AC Line Dropout/Holdup	33
3.2.5.5 AC Line Fuse	33
3.2.5.6 AC Inrush	34
3.2.5.7 AC Line Leakage Current	34
3.2.5.8 AC Line Transient Specification	34
3.2.5.9 Susceptibility Requirements	34
3.2.5.10 Electrostatic Discharge Susceptibility	35
3.2.5.11 Fast Transient/Burst	35
3.2.5.12 Radiated Immunity	35
3.2.5.13 Surge Immunity	35
3.2.5.14 Power Recovery	35
3.2.5.15 Voltage Interruptions	35
3.2.6 DC Output Specification	36
3.2.6.1 Output Power/Currents	36
3.2.6.2 Standby Output	36
3.2.7 Protection Circuits	36
3.2.7.1 Current Limit (OCP)	36
3.2.7.2 Over Voltage Protection (OVP)	37
3.2.7.3 Over Temperature Protection (OTP)	37
4 Thermal Management	38
4.1 Thermal Operation and Configuration Requirements	38
4.2 Thermal Management Overview	39
4.2.1 Set Throttling Mode	39
4.2.2 Altitude	40
4.2.3 Set Fan Profile	40
4.2.4 Fan PWM Offset	40
4.2.5 Quiet Fan Idle Mode	40
4.2.6 Thermal Sensor Input for Fan Speed Control	40
4.3 System Fans	42
4.4 FRUSDR Utility	44
5 System Storage and Peripheral Options	45
5.1 2.5” Hard Disk Drive Support	45
5.1.1 2.5” Drive Hot-Swap Backplane Overview	46
5.1.2 Cypress* CY8C22545 Enclosure Management Controller	47
5.2 3.5” Hard Disk Drive Support	47
5.2.1 3.5” Drive Hot-Swap Backplane Overview	48
5.2.2 Cypress* CY8C22545 Enclosure Management Controller	49
5.3 SATA DOM Support	49
6 Storage Controller Options Overview	50
6.1 Embedded SATA Controller Support	50
7 Front Control Panel and I/O Panel Overview	51
7.1 I/O Panel Features	51
7.2 Control Panel Features	51
8 Intel® Local Control Panel	56
8.1 LCD Functionality	56
8.2 Main Menu	57
8.3 Event Menu	58
8.4 View Menu	58
8.4.1 System FW Version (SysFwVer)	58
8.4.2 System Information (SysInfo)	59
8.4.3 BMC IP Configuration	59
8.4.4 RMM4 IP Configuration	59
8.4.5 Power	60
8.4.6 Last Post Code (Last PC)	60
8.5 Config Menu	60
8.5.1 IP Version	60
8.5.2 BMC IP	60
8.5.3 RMM4 IP	62
8.5.4 Boot Device	62
8.5.5 Banner	62
9 PCIe Support and Riser Card Support	64
9.1 Architectural Overview of the Server Board Riser Slots	64
Appendix A: Integration and Usage Tips	67
Appendix B: POST Code LED Decoder	68
Appendix C: POST Code Errors	73
Glossary	79

Match case Limit results 1 per page

Appendix A: Integration and Usage Tips

Intel

Server System R1000RP Family TPS

Revision 1.2

Intel

order number: G91532-003

Appendix A: Integration and Usage Tips

Before attempting to integrate and configure your system, you should reference this section,

which provides a list of useful information.



After the system is integrated with processors, memory, and peripheral devices, the

FRUSDR utility

must

be run to load the proper Sensor Data Record data to the

integrated Server Management subsystem. Failure to run this utility may prevent Server

Management from accurately monitoring system health and may affect system

performance. The FRUSDR utility for this server system can either be run from the Intel

Deployment CDROM that came with your system or can be downloaded from the Intel

website referenced at the bottom of this page.



To ensure the highest system reliability, make sure the latest system software is loaded

on the server before deploying the system onto a live networking environment. This

includes system BIOS, FRUSDR, BMC firmware, and hot-swap controller firmware. The

system software can be updated using the Intel

Deployment DVD that came with your

system or can be downloaded from the Intel

website referenced at the bottom of this

page.



System fans are not hot-swappable.



Only supported memory validated by Intel should be used in this server system. A list of

supported memory can be found in the

Intel

Server Board S1200V3RP Tested Memory

List

which can be downloaded from the Intel

website referenced at the bottom of this

page.



This system supports the Intel

Xeon

processor E3-1200 V3 series. You cannot use

Intel

Xeon

processors not referenced on the supported processor list in this server

system.



You must use the CPU/memory air duct to maintain system thermals.



To maintain system thermals, you must populate all hard drive bays with either a hard

drive or drive blank.



You must remove AC power from the system prior to opening the chassis for service.

You can download the latest system documentation, drivers, and system software from the

Intel

Support website at

http://www.intel.com/p/en_US/support/highlights/server/R1000RP