Intel SC450NX Product Guide - Page 101

Removing a 5.25-inch Peripheral from the Front Bay, If you leave the bay empty

Get Intel SC450NX - Server Platform - 0 MB RAM PDF manuals and user guides View all Intel SC450NX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Removing a 5.25-inch Peripheral from the Front Bay 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. Open the front bezel by rotating its right side out and to the left. 3. Disconnect the power and signal cables from the drive. 4. The drive has two protruding plastic, snap-in rails attached. Squeeze the rail tabs toward each other as you carefully slide the drive forward out of the bay, and place it on an antistatic surface. 5. Remove and save the four screws and two slide rails. 6. If you leave the bay empty, install a stainless steel EMI shield on the bay for proper cooling and airflow. 7. If you do not replace the device with another SCSI device, and it was installed at the end of the SCSI signal cable, modify the cable and termination arrangement so that a proper termination exists at the end of the cable (it can be a termination device only, not necessarily a SCSI peripheral). 8. Close the front bezel. C D B E A C Figure 32. Installing a Removable Media Device A. Removable media device B. Drive rail C. Rail tab D. Power cable E. Typical SCSI signal cable OM08003 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
101
Removing a 5.25-inch Peripheral from the Front Bay
1.
Observe the safety and ESD precautions at the beginning of this chapter.
2.
Open the front bezel by rotating its right side out and to the left.
3.
Disconnect the power and signal cables from the drive.
4.
The drive has two protruding plastic, snap-in rails attached.
Squeeze the rail tabs toward each
other as you carefully slide the drive forward out of the bay, and place it on an antistatic
surface.
5.
Remove and save the four screws and two slide rails.
6.
If you leave the bay empty, install a stainless steel EMI shield on the bay for proper cooling
and airflow.
7.
If you do not replace the device with another SCSI device, and it was installed at the end of the
SCSI signal cable, modify the cable and termination arrangement so that a proper termination
exists at the end of the cable (it can be a termination device only, not necessarily a
SCSI peripheral).
8.
Close the front bezel.
C
OM08003
C
A
B
D
E
Figure 32.
Installing a Removable Media Device
A.
Removable media device
B.
Drive rail
C.
Rail tab
D.
Power cable
E.
Typical SCSI signal cable