Intel SC450NX Product Guide - Page 95

Diskette Drive, Removing the Diskette Drive

Get Intel SC450NX - Server Platform - 0 MB RAM PDF manuals and user guides View all Intel SC450NX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Diskette Drive Removing the Diskette Drive 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. Remove the access cover (see page 89). 3. Disconnect the power and signal cables from the diskette drive. The connectors are keyed for ease in reconnecting them to the drive. 4. Remove and save the screw that secures the diskette drive carrier to the 5.25-inch drive bay. B A OM08011a Figure 27. Removing the Diskette Drive from the Chassis A Power cable B Signal cable 5. Slide the carrier toward the back of the chassis to disengage the tabs from the slots in the bottom of the 5.25-inch drive bay. 6. Remove the carrier/drive from the chassis, and place it component-side up on an antistatic surface. 7. Remove the three screws that hold the carrier to the drive, and set them and the carrier aside. 8. Place the drive in an antistatic protective wrapper if you are not reinstalling the same drive. 9. Reinstall the access cover using the original screws. 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
95
Diskette Drive
Removing the Diskette Drive
1.
Observe the safety and ESD precautions at the beginning of this chapter.
2.
Remove the access cover (see page 89).
3.
Disconnect the power and signal cables from the diskette drive.
The connectors are keyed for
ease in reconnecting them to the drive.
4.
Remove and save the screw that secures the diskette drive carrier to the 5.25-inch drive bay.
OM08011a
A
B
Figure 27.
Removing the Diskette Drive from the Chassis
A
Power cable
B
Signal cable
5.
Slide the carrier toward the back of the chassis to disengage the tabs from the slots in the
bottom of the 5.25-inch drive bay.
6.
Remove the carrier/drive from the chassis, and place it component-side up on an antistatic
surface.
7.
Remove the three screws that hold the carrier to the drive, and set them and the carrier aside.
8.
Place the drive in an antistatic protective wrapper if you are not reinstalling the same drive.
9.
Reinstall the access cover using the original screws.