Intermec CS40 CS40 Mobile Computer User's Manual - Page 87

Configuring Static WEP Security With Funk, Using Open No Security Associations With Funk

Get Intermec CS40 PDF manuals and user guides View all Intermec CS40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Chapter 7 - Configuring the Computer Configuring Static WEP Security With Funk After you configure the communications and radio parameters on your mobile computer and select Funk as your security choice, you can configure static WEP security with Funk. Intermec recommends that you use WPA2-PSK instead of WEP if possible. To configure static WEP security with Funk security: 1 Start Intermec Settings. 2 Choose Communications > 802.11 Radio > Funk Security. 3 Select the profile you want to configure. 4 For Association, choose Open. 5 For Encryption, choose WEP. 6 For 8021x choose None. 7 Define a value for the keys you want to use. You can define up to four keys (Key 1 through Key 4). Enter an ASCII key or a hex key that is either 5 bytes or 13 bytes long depending on the capability of the radio. Set a 5- byte value for 64-bit WEP or a 13-byte value for 128-bit WEP. Hex keys must be preceded by 0x and contain 5 or 13 hex pairs. 8 For Transmit key, choose the key you want to use for transmitting data. 9 Save your settings. Using Open (No Security) Associations With Funk You can configure your mobile computer for no security with Funk. To configure Open security with Funk: 1 Start Intermec Settings. 2 Choose Communications > 802.11 Radio > Funk Security. 3 Select the active profile you are using. 4 For Association, choose Open. 5 For Encryption, choose None. 6 Tap OK. Your settings are saved. CS40 Mobile Computer User's Manual 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Chapter 7 — Configuring the Computer
CS40 Mobile Computer User’s Manual
75
Configuring Static WEP Security With Funk
After you configure the communications and radio parameters on
your mobile computer and select Funk as your security choice, you can
configure static WEP security with Funk. Intermec recommends that
you use WPA2-PSK instead of WEP if possible.
To configure static WEP security with Funk security:
1
Start Intermec Settings.
2
Choose
Communications >
802.11 Radio > Funk Security
.
3
Select the profile you want to configure.
4
For
Association
, choose
Open
.
5
For
Encryption
, choose
WEP
.
6
For
8021x
choose
None
.
7
Define a value for the keys you want to use. You can define up to
four keys (
Key 1
through
Key 4
).
Enter an ASCII key or a hex key that is either 5 bytes or 13 bytes
long depending on the capability of the radio. Set a 5- byte value for
64-bit WEP or a 13-byte value for 128-bit WEP. Hex keys must be
preceded by 0x and contain 5 or 13 hex pairs.
8
For
Transmit key
, choose the key you want to use for transmitting
data.
9
Save your settings.
Using Open (No Security) Associations With Funk
You can configure your mobile computer for no security with Funk.
To configure Open security with Funk:
1
Start Intermec Settings.
2
Choose
Communications >
802.11 Radio > Funk Security
.
3
Select the active profile you are using.
4
For
Association
, choose
Open
.
5
For
Encryption
, choose
None
.
6
Tap
OK
. Your settings are saved.