Kenwood TS-480HX Operation Manual - Page 26
Operating Basics
View all Kenwood TS-480HX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 26 highlights
OPERATING BASICS SWITCHING POWER ON/ OFF 1 Switch the DC power supply(s) ON if you are using a DC power supply(s). 2 Press and hold [ ] (POWER) briefly to switch the transceiver ON. HF/50MHz ALL MODE TRANSCEIVER TS-480 PF ANT 1/2 ATT/PRE AT AF SQL 1 REC 2 REC CH1 CH2 4 TX MONI 5 RF.G PWR MIC 7 8 NB/T VOX CLR 0 OFF MTR AGC 3 REC CH3 6 DELAY KEY 9 PROC ENT DNL NAR NR FIL BC CW.T STEP SG.SEL FINE SCAN MODE F.LOCK MENU MHz CL XIT RIT M.IN QMI M VFO QMR M/V A / B SPLIT A=B TF-SET MULTI IF SHIFT • Do not press the switch for more than approximately 2 seconds; the transceiver will be switched OFF. • TS-480HX only: If "RX ONLY" appears on the sub-display upon power up, confirm that two DC cable connectors are securely connected to the DC-1 and DC-2 connectors. When this warning message appears, you can receive signals as usual but you cannot transmit even if you decrease the output power. "TWIN PWR" appears when two DC power cables are connected to the DC-1 and DC-2 connectors. • Upon power up, "HELLO" appears on the main display, followed by the selected frequency and other indicators. 3 To switch the transceiver OFF, press [ ] (POWER) again. 4 Switch the DC power supply(s) OFF. • You may skip step 3. After switching the transceiver ON, you can switch it OFF or ON using only the power switch of the DC power supply(s). The transceiver remembers the information of the POWER switch position when the DC power source is switched OFF. ADJUSTING VOLUME AF (AUDIO FREQUENCY) GAIN Turn the AF control clockwise to increase the audio level and counterclockwise to decrease the level. AF SQL HF/50MHz ALL MODE TRANSCEIVER TS-480 PF ANT 1/2 ATT/PRE AT AF SQL 1 REC 2 REC CH1 CH2 4 TX MONI 5 RF.G PWR MIC 7 8 NB/T VOX CLR 0 OFF MTR AGC 3 REC CH3 6 DELAY KEY 9 PROC ENT DNL NAR NR FIL BC STEP FINE CW.T SG.SEL SCAN MODE F.LOCK MENU MHz CL XIT RIT M.IN QMI M VFO QMR M/V A / B SPLIT A=B TF-SET MULTI IF SHIFT Note: The position of the AF control does not affect the volume of beeps caused by pressing keys nor the CW TX sidetone. The audio level for Digital mode operation is also independent of the AF control setting. 18 RF (RADIO FREQUENCY) GAIN The RF gain is normally configured to the maximum level regardless of the operating modes. The transceiver has been configured to the maximum level at the factory. However, you may decrease the RF gain slightly when you have trouble hearing the desired signal because of excessive atmospheric noise or interference from other stations. First, take note of the peak S-meter reading of the desired signal. 1 Press [MIC/ RF.G] (1 s). HF/50MHz ALL MODE TRANSCEIVER TS-480 PF ANT 1/2 ATT/PRE AT 1 REC 2 REC 3 REC AF SQL CH1 CH2 4 TX MONI 5 RF.G PWR MIC CH3 6 DELAY KEY DNL NAR NR FIL MODE F.LOCK 7 8 9 NB/T VOX PROC MENU BC CW.T CLR 0 OFF STEP SG.SEL MTR AGC ENT FINE SCAN MHz CL XIT RIT M.IN QMI M VFO QMR M/V A / B SPLIT A=B TF-SET MULTI IF SHIFT • The current RF gain level appears on the sub-display (0: minimum ~ 100: maximum). 2 Turn the MULTI control counterclockwise until the S-meter reads the peak value that you noted. HF/50MHz ALL MODE TRANSCEIVER TS-480 PF ANT 1/2 ATT/PRE AT AF SQL 1 REC 2 REC CH1 CH2 4 TX MONI 5 RF.G PWR MIC 7 8 NB/T VOX CLR 0 OFF MTR AGC 3 REC CH3 6 DELAY KEY 9 PROC ENT DNL NAR NR FIL BC STEP FINE CW.T SG.SEL SCAN MODE F.LOCK MENU MHz CL XIT RIT M.IN QMI M VFO QMR M/V A / B SPLIT A=B TF-SET MULTI IF SHIFT • Signals that are weaker than this level will be attenuated and reception of the station will become easier. Depending on the type and gain of your antenna, and the condition of the band, adjust the RF gain. When using FM mode, always adjust the RF gain to the maximum level. SELECTING VFO A OR VFO B Two VFOs are available for controlling the frequency on the transceiver. Each VFO (VFO A and VFO B) works independently so that a different frequency and mode can be selected. For example, when SPLIT operation is activated, VFO A is used for reception and VFO B is used for transmission. The opposite combination is also possible. Press [A/B / M/V] to toggle between VFO A and B. HF/50MHz ALL MODE TRANSCEIVER TS-480 PF ANT 1/2 ATT/PRE AT 1 REC 2 REC 3 REC CH1 CH2 CH3 AF SQL 4 TX MONI 5 RF.G 6 DELAY PWR MIC KEY 7 8 9 NB/T VOX PROC CLR 0 OFF MTR AGC ENT DNL NAR NR FIL BC CW.T STEP SG.SEL FINE SCAN MODE F.LOCK MENU MHz CL XIT RIT M.IN QMI M VFO QMR M/V A / B SPLIT A=B TF-SET MULTI IF SHIFT • "tA" or "tB" appears to indicate which VFO is selected.