Konica Minolta Kodak Ngenuity 9150 User Guide - Page 24

Maintenance, Manual Feed, Normal ADF, Manual, Feed modes, ADF mode, Manual mode, Assisted Manual mode

Get Konica Minolta Kodak Ngenuity 9150 PDF manuals and user guides View all Konica Minolta Kodak Ngenuity 9150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Maintenance - this yellow LED indicates that maintenance or service conditions exist in the scanner. Maintenance LED Off (not lit) Slow blinking Fast blinking Steady on Scanner state No maintenance is required at this time. Maintenance is needed. See the section entitled, "Ngenuity Operator Utility" (Maintenance monitor) later in this chapter for more information. Scanner is busy or offline. This occurs when the scanner is in off-line mode and not capable of scanning (i.e., ADF test, camera calibration, downloading firmware, imprinter cleaning, etc.). Scanner self-test fault detected; scanner service may be required. Use the NOU for more information on the self test failure. Manual Feed - this green LED indicates that the feed mode has been changed from the default, Normal ADF (Automatic Document Feeder), to Manual feed mode. When the LED is illuminated, the scanner is in Manual feed mode. Feed modes: the Ngenuity Scanner has four feed modes for feeding documents into the scanner's transport: • ADF mode (default) - used for feeding batches of documents that are similar in size and weight. After a batch of documents is placed on the feeder table, the batch is fed automatically into the scanner's transport. • Manual mode - this mode is used to feed exception documents that cannot be fed in ADF mode (e.g.,multiple forms). In this mode, you must feed documents manually into the scanner one at a time. When scanning in Manual mode, the Manual Feed LED on the control panel will be lit. See the section entitled, "Manually feeding documents" in Chapter 3 for more information. • Assisted Manual mode - once the scanner has entered Manual Feed mode, the skimmer can be lowered onto the feeder table to enable Assisted Manual mode. In this mode, the paper sensor on the feeder table will trigger the skimmer to pull the documents into the scanner transport. This mode can also be used to automatically feed small batches while the scanner is in Manual Feed mode. • Test Feed mode - used to test and verify the scanner's feeding capabilities, as well as to feed transport cleaning sheets. This mode allows you to feed documents without generating a scan command from the host PC. Unlike ADF and Manual (Assisted) modes, the Test Feed mode button is set from within Custom Functions in the Ngenuity Operator Utility. NOTE: With the exception of the Test Feed mode, all feed modes are set through the scanning application's scanner properties within the scanning software application. 4-4 A-61662 October 2011

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
4-4
A-61662
October 2011
Maintenance
— this yellow LED indicates that maintenance or service
conditions exist in the scanner.
Manual Feed
— this green LED indicates that the feed mode has been
changed from the default,
Normal ADF
(Automatic Document Feeder),
to
Manual
feed mode. When the LED is illuminated, the scanner is in
Manual
feed mode.
Feed modes:
the
Ngenuity
Scanner has four feed modes for feeding
documents into the scanner’s transport:
•
ADF mode
(default) — used for feeding batches of documents that
are similar in size and weight. After a batch of documents is placed
on the feeder table, the batch is fed automatically into the scanner’s
transport.
•
Manual mode
— this mode is used to feed exception documents that
cannot be fed in ADF mode (e.g.,multiple forms). In this mode, you
must feed documents manually into the scanner one at a time. When
scanning in Manual mode, the
Manual Feed
LED on the control
panel will be lit. See the section entitled, “Manually feeding
documents” in Chapter 3 for more information.
•
Assisted Manual mode
— once the scanner has entered Manual
Feed mode, the skimmer can be lowered onto the feeder table to
enable Assisted Manual mode. In this mode, the paper sensor on the
feeder table will trigger the skimmer to pull the documents into the
scanner transport. This mode can also be used to automatically feed
small batches while the scanner is in Manual Feed mode.
•
Test Feed mode
— used to test and verify the scanner’s feeding
capabilities, as well as to feed transport cleaning sheets. This mode
allows you to feed documents without generating a scan command
from the host PC.
Unlike ADF and Manual (Assisted) modes, the Test Feed mode button
is set from within
Custom Functions
in the Ngenuity Operator Utility.
NOTE: With the exception of the Test Feed mode, all feed modes are
set through the scanning application’s scanner properties within
the scanning software application.
Maintenance LED
Scanner state
Off (not lit)
No maintenance is required at this time.
Slow blinking
Maintenance is needed. See the section
entitled, “Ngenuity Operator Utility”
(Maintenance monitor) later in this chapter for
more information.
Fast blinking
Scanner is busy or offline. This occurs when the
scanner is in off-line mode and not capable of
scanning (i.e., ADF test, camera calibration,
downloading firmware, imprinter cleaning, etc.).
Steady on
Scanner self-test fault detected; scanner service
may be required. Use the NOU for more
information on the self test failure.