Konica Minolta Kodak Ngenuity 9150 User Guide - Page 59

Cleaning the optics, imaging guides, camera glass covers

Get Konica Minolta Kodak Ngenuity 9150 PDF manuals and user guides View all Konica Minolta Kodak Ngenuity 9150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Cleaning the optics Optics include the imaging guides, camera glass covers and sensors. All of the optics components should be cleaned at the same time. NOTE: The lamps are not part of the optics. The lamps (LEDs) should not be cleaned with wipes or solvents. Cleaning the imaging guides and camera glass covers To prevent streaks in images, reduced OCR/ICR/Barcode recognition rates, blurred images, etc., you should clean the imaging guides every 50,000 pages. The two imaging guides which are inside black, plastic frames are located in the top and bottom transport trays. When removing an imaging guide for cleaning or replacement, the entire assembly (imaging guide and frame) are removed and replaced as one piece. Clean the camera glass covers at the same time you clean the imaging guides. CAUTION: Do not remove the imaging guide from the black frame. 1. Open the scanner cover. 2. Gently pull the 2 fastening clips that secure the top imaging guide towards the front of the scanner to release and remove the imaging guide from the transport. Fastening clips (2) 3. Using a Staticide wipe, clean both sides of the imaging guide. Be careful not to touch the cleaned glass. IMPORTANT:Staticide wipes contain isopropanol which can cause eye irritation and dry skin. Wash your hands with soap and water after performing maintenance procedures. Refer to the Material Data Safety Sheet (MSDS) for more information. The MSDS is available on the Kodak web site at www.kodak.com/go/MSDS. A-61662 October 2011 6-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
A-61662
October 2011
6-7
Cleaning the optics
Optics include the
imaging guides, camera glass covers
and
sensors
. All of the optics components should be cleaned at the same
time.
NOTE: The lamps are not part of the optics. The lamps (LEDs) should
not be cleaned with wipes or solvents.
Cleaning the imaging guides and camera glass covers
To prevent streaks in images, reduced OCR/ICR/Barcode recognition
rates, blurred images, etc., you should clean the imaging guides every
50,000 pages.
The two imaging guides which are inside black, plastic frames are
located in the top and bottom transport trays. When removing an
imaging guide for cleaning or replacement, the entire assembly
(imaging guide and frame) are removed and replaced as one piece.
Clean the camera glass covers at the same time you clean the imaging
guides.
CAUTION: Do not remove the imaging guide from the black frame.
1.
Open the scanner cover.
2.
Gently pull the 2 fastening clips that secure the top imaging guide
towards the front of the scanner to release and remove the imaging
guide from the transport.
3.
Using a Staticide wipe, clean both sides of the imaging guide. Be
careful not to touch the cleaned glass.
IMPORTANT:Staticide wipes contain isopropanol which can cause
eye irritation and dry skin. Wash your hands with soap
and water after performing maintenance procedures.
Refer to the Material Data Safety Sheet (MSDS) for
more information. The MSDS is available on the
Kodak web site at
www.kodak.com/go/MSDS
.
Fastening clips (2)