Konica Minolta bizhub 501 bizhub 361/421/501 Box Operations User Manual - Page 226

Error message list

Page 226 highlights

Appendix 10 10 10.1 Appendix Error message list If an error message appears, perform the corresponding operation described below. Message Unable to connect to the network. Cause and solution A connection to the network could not be established. Check if the network cable is correctly connected. In addition, check that the "Network Settings" parameters in Administrator mode have been correctly specified. 2 The address for the communication method cannot be selected since the number of addresses has exceeded the maximum allowed for broadcasting. Document could not be saved in user box due to insufficient HDD capacity. Check log. The number of registered user boxes has reached the max. allowance. The number of documents saved in the User Box has reached its maximum. The number of programmed jobs has reached the max. allowance. Wait until a programmed job is completed. Note For details on the network settings, refer to the User's Guide [Network Administrator]. The number of destinations specified exceeds the number possible for a broadcast transmission. Reduce the number of broadcast destinations, or send the transmission in multiple batches. The hard disk is full. Delete unnecessary data, and then try saving the data again. The number of user boxes that can be registered has reached the maximum number possible. Delete unnecessary user boxes, and then try registering new boxes again. The number of documents that can be saved in a user box has reached the maximum number possible. Delete unnecessary documents, and then try saving the document again. The number of jobs that can be programmed has reached the maximum number possible. Wait until a job has been completed, or delete a current job. 501/421/361 10-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237

501/421/361
10-2
Appendix
10
10
Appendix
10.1
Error message list
If an error message appears, perform the corresponding operation described below.
Message
Cause and solution
Unable to connect to the network.
A connection to the network could not be established. Check if the network
cable is correctly connected. In addition, check that the "Network Settings"
parameters in Administrator mode have been correctly specified.
2
Note
For details on the network settings, refer to the User’s Guide [Network
Administrator].
The address for the communication
method cannot be selected since the
number of addresses has exceeded
the maximum allowed for broadcast-
ing.
The number of destinations specified exceeds the number possible for a
broadcast transmission. Reduce the number of broadcast destinations, or
send the transmission in multiple batches.
Document could not be saved in user
box due to insufficient HDD capacity.
Check log.
The hard disk is full. Delete unnecessary data, and then try saving the data
again.
The number of registered user boxes
has reached the max. allowance.
The number of user boxes that can be registered has reached the maximum
number possible. Delete unnecessary user boxes, and then try registering
new boxes again.
The number of documents saved in
the User Box has reached its maxi-
mum.
The number of documents that can be saved in a user box has reached the
maximum number possible. Delete unnecessary documents, and then try
saving the document again.
The number of programmed jobs has
reached the max. allowance. Wait un-
til a programmed job is completed.
The number of jobs that can be programmed has reached the maximum
number possible. Wait until a job has been completed, or delete a current
job.