Home » Lantronix Manuals » Electronics Accessories » Lantronix SpiderDuo » Manual Viewer

Lantronix SpiderDuo Lantronix Spider / SpiderDuo - User Guide - Page 117

USB Host Disk Commands, connect wakeonlan macaddr, usbhost disk mount drive, usbhost disk dump

View all Lantronix SpiderDuo manuals

Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

11: Command Reference Description Sends a WOL packet to a specified device. connect wakeonlan macaddr Syntax connect wakeonlan macaddr [MAC Address] [password ] Note: MAC address must be in hex format: 'XX:XX:XX:XX:XX:XX' Description Sends a WOL packet to specified MAC address. USB Host Disk Commands Note: The following USB Host Disk commands are available for the SpiderDuo device only. usbhost disk mount drive Syntax usbhost disk mount drive Description Mounts a USB thumb drive to use as a storage device. The USB thumb drive must be formatted with an fat filesystem and drive must support USB high speed mode. usbhost disk unmount drive Syntax usbhost disk unmount drive Description Unmounts the USB thumb drive. usbhost disk dir drive Syntax usbhost disk dir drive Description Displays a directory listing of a USB thumb drive. usbhost disk dump Syntax usbhost disk dump Spider™ and SpiderDuo® KVM-over-IP Device User Guide 117

Section	Page
Spider and SpiderDuo KVM-over-IP Device User Guide	1
Copyright and Trademark	2
LINUX GPL Compliance	2
Warranty	2
Contacts	2
Sales Offices	2
Disclaimer and Revisions	3
Documentation Changes	3
Revision History	3
Table of Contents	4
List of Figures	10
List of Tables	12
1: About This Guide	13
Chapter and Appendix Summaries	13
Conventions	14
Additional Documentation	15
2: Overview	16
Spider Overview	16
Features	16
Functionality	17
System Configuration and Cables	17
Technical Specifications	19
SpiderDuo Overview	20
Features	20
Functionality	20
System Configuration and Cables	21
Technical Specifications	22
Product Information Label	23
3: Installing the Spider Device	25
Package Contents	25
Installing the Spider	25
Detector Installation and IP Address Reset	28
Target Computer Setup	30
Video Resolutions and Refresh Rates Configuration	31
Mouse-to-Cursor Synchronization	31
Telnet/SSH Connections to Serial Ports	32
Cable Connections for KVM and USB	32
Device Failure or Cable Break in the Daisy Chain	32
Client Server Setup	33
Network Environment	33
Spider Power	33
4: Installing the SpiderDuo Device	34
Package Contents	34
Installing the SpiderDuo	34
Detector Installation and IP Address Reset	37
Target Computer Setup	39
Video Resolutions and Refresh Rates Configuration	40
Mouse-to-Cursor Synchronization	40
Telnet/SSH Connections to Serial Ports	41
Cable Connections for KVM and USB	41
Power Sequencing	41
Client Server Setup	41
Network Environment	42
PCU Power	43
5: Web Browser Access	45
Accessing the KVM Console	45
6: Remote System Control	46
Overview	46
Remote Console Window	46
Main Viewport and Scroll Bars	47
Button Keys	47
Toolbar	47
Options	48
Information Bar - Connection	48
Information Bar - Resolution	48
Information Bar - Network Traffic	48
Concurrent Access State	48
Monitor Only State	48
Exclusive Access	48
Basic Remote Console Operation	49
Auto Video Adjustment	50
Screen Display Adjustments	50
Fast Sync and Intelligent Sync	50
Single and Double Mouse Modes	50
Local Cursor	50
Optimizing Video	51
Auto and Manual Video Adjustment	51
Clock and Phase	51
Video Encoding	51
Scaling Target Video to Client Resolution	52
Keyboard Functions	52
Soft Keyboard	52
Local Keyboard	52
Hotkeys	52
Other Remote Console Functions	53
Monitor Only	53
Exclusive Access	53
Screenshot to Clipboard	53
Refresh Video	53
Telnet/SSH	53
Set up and Enable	53
Passthrough Use	54
Telnet Console Use	54
7: Interfaces	56
Network Settings	56
Network Basic Settings	57
Lan Interface Settings	58
IPv6 Settings (Firmware v3.0 or higher)	58
Miscellaneous Network Settings	58
Serial Port Settings	60
KVM Console Settings	61
KVM Console Settings	62
Transmission Encoding	63
KVM Console Type	63
KVM Console Deployment	63
Miscellaneous KVM Console Settings	63
Mouse Hotkey	64
KVM Console Virtual Keys	64
Keyboard/Mouse	65
Keyboard/Mouse Settings	66
Keyboard Model	66
Key Release Timeout	66
Country Code	66
USB Mouse Type	67
Mouse Speed	67
Video	68
Virtual Media	69
Virtual Media Active Image	70
Drive Redirection	70
Virtual Media Options	71
Image on Windows Share	71
Floppy Image	72
Connecting to a Redirected Drive	73
User Interface Settings	75
8: User Accounts	76
Local vs. Remote Authentication	76
Local User Management	76
Modifying Passwords	76
User and Group Management	77
User Management	78
Group Management	79
User Permissions	79
Remote Authentication	80
LDAP	81
RADIUS	82
9: Services	83
Date/Time	83
Security	84
HTTP Encryption	85
Login Limitations	85
KVM Encryption	85
Group Based System Access Control	86
Authentication Limitation	86
Certificate	87
Event Log	89
Event Log Targets	89
Event Log Assignments	90
SNMP	90
KVM Search	92
Power Management	93
SpiderDuo Power Control Unit	94
Wake-On LAN	94
Enable WOL	95
Remove Entries, Reset to Defaults, or Reset	95
10: Maintenance	96
Device Status	96
Configuration	97
Update Firmware	99
View Event Log	99
Unit Reset	100
iGoogle Gadgets	101
11: Command Reference	104
Command Syntax	104
Command Help	105
Tips	105
Configuration Commands	105
Connect Commands	107
User Group Commands	112
OEM Customization Commands	115
Power Commands	115
Serial Port Commands	116
WOL (Wake on LAN) Commands	116
USB Host Disk Commands	117
Reboot Commands	118
Diagnostic Commands	118
Group Permissions	118
Appendix A: Troubleshooting	120
Appendix B: Virtual Media Example	122
Goal	122
Step 1 – Prepare the VM Server	122
Step 2 – Enable Virtual Media	123
Step 3 – Use the Virtual Media	125
Appendix C: Supported Resolutions and Refresh Rates	127
Appendix D: Mounting Bracket Kit	128
Appendix E: PCU Safety Information	130
Cover	130
Power Plug	130
Input Supply	130
Grounding	130
Fuses	130
Appendix F: Technical Support	131
Technical Support US	131
Technical Support Europe, Middle East, Africa	131