Lantronix SpiderDuo Lantronix Spider / SpiderDuo - User Guide - Page 36

IP Configuration, config, Enter, Table 4-3, SpiderDuo Indicator LEDs

Get Lantronix SpiderDuo PDF manuals and user guides View all Lantronix SpiderDuo manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

4: Installing the SpiderDuo Device Label ID SysOK PCU Figure 4-2 SpiderDuo Local KVM, USB, Computer Input and Serial Ports Computer Input Pinouts 1 RTS (out) 2 PCU +5V (out) 3 TX (out) 4 PCu Sense (in) 5 GND (out) 6 RX (in) 7 PCU Drive (out) 8 CTS (in) Color Amber Blue Green Table 4-3 SpiderDuo Indicator LEDs Action On - Unit ID Selected Blinking -Thumb-drive Configuration Successful On - Powered up and OK Blinking - Booting On - Power Unit Connected, AC power is passed through 5. Upon bootup, the terminal window displays the IP Configuration screen. At the command prompt type config and press Enter. Figure 4-4 SpiderDuo Welcome Screen 6. To change the default IP auto configuration from DHCP to a static IP address, at the IP autoconfiguration prompt type none and press Enter. Figure 4-5 SpiderDuo Default IP Configuration Screen 7. Follow the prompts to enter the IP address, subnet mask, default gateway, and LAN interface information. 8. Type Enter, to accept the changes. The system takes about 20 seconds to complete. Type Enter once again at the prompt to display the updated IP address. 9. Plug an Ethernet cable connected to your network into the Ethernet port. The Link LED illuminates. Spider™ and SpiderDuo® KVM-over-IP Device User Guide 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
4: Installing the SpiderDuo Device
Spider™ and SpiderDuo® KVM-over-IP Device User Guide
36
Figure 4-2
SpiderDuo Local KVM, USB, Computer Input and Serial Ports
5.
Upon bootup, the terminal window displays the
IP Configuration
screen. At the command
prompt type
config
and press
Enter
.
Figure 4-4
SpiderDuo Welcome Screen
6.
To change the default IP auto configuration from DHCP to a static IP address, at the
IP
autoconfiguration
prompt type
none
and press
Enter
.
Figure 4-5
SpiderDuo Default IP Configuration Screen
7.
Follow the prompts to enter the IP address, subnet mask, default gateway, and LAN interface
information.
8.
Type
Enter
, to accept the changes. The system takes about 20 seconds to complete. Type
Enter
once again at the prompt to display the updated IP address.
9.
Plug an Ethernet cable connected to your network into the Ethernet port. The Link LED
illuminates.
Pinouts
1 RTS
(out)
2 PCU +5V
(out)
3 TX
(out)
4 PCu Sense
(in)
5 GND
(out)
6 RX
(in)
7 PCU Drive
(out)
8 CTS
(in)
Table 4-3
SpiderDuo Indicator LEDs
Label
Color
Action
ID
Amber
On - Unit ID Selected
Blinking -Thumb-drive Configuration Successful
SysOK
Blue
On - Powered up and OK
Blinking - Booting
PCU
Green
On - Power Unit Connected,
AC power is passed through
Computer Input