Lantronix SpiderDuo Lantronix Spider / SpiderDuo - User Guide - Page 95

Enable WOL, Remove Entries, Reset to Defaults, or Reset, Send to the MAC address below, Wake Up

Get Lantronix SpiderDuo PDF manuals and user guides View all Lantronix SpiderDuo manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

9: Services If the second radio button is selected, the WOL message may be sent to any number of devices identified by a Device Name, IP Address (optional), or MAC address (entered into the respective text boxes). If no password is needed, this field should be left blank. WOL support is implemented on the motherboard of a computer and the network interface and is not dependent on the operating system running on the hardware, although the operating system can sometimes control the WOL behavior. Refer to your motherboard and operating system user guide for configuration information. Enable WOL To enable WOL, perform the following steps. 1. Enter the MAC address and password in the Send to the MAC address below field. 1. Click Wake Up. Or 2. Enter the device name, IP address, MAC address, and password in the Send to the following devices field. 3. Click Add More Entries if required. Repeat Step 2 for each additional entry. 4. Click Wake Up. Remove Entries, Reset to Defaults, or Reset To remove an entry from the Send to the following devices table, clear the Device Name field and click Save. To reset to defaults, click Reset to Defaults. To reset, click Reset. Spider™ and SpiderDuo® KVM-over-IP Device User Guide 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
9: Services
Spider™ and SpiderDuo® KVM-over-IP Device User Guide
95
If the second radio button is selected, the WOL message may be sent to any number of devices
identified by a Device Name, IP Address (optional), or MAC address (entered into the respective
text boxes).
If no password is needed, this field should be left blank.
WOL support is implemented on the motherboard of a computer and the network interface and is
not dependent on the operating system running on the hardware, although the operating system
can sometimes control the WOL behavior. Refer to your motherboard and operating system user
guide for configuration information.
Enable WOL
To enable WOL, perform the following steps.
1.
Enter the MAC address and password in the
Send to the MAC address below
field.
1.
Click
Wake Up
.
Or
2.
Enter the device name, IP address, MAC address, and password in the
Send to the
following devices
field.
3.
Click
Add More Entries
if required. Repeat Step 2 for each additional entry.
4.
Click
Wake Up
.
Remove Entries, Reset to Defaults, or Reset
To remove an entry from the
Send to the following devices
table, clear the
Device Name
field
and click
Save
.
To reset to defaults, click
Reset to Defaults
.
To reset, click
Reset
.