NEC NP-PA622U User's Manual - Page 142

Connecting an External Monitor, when displaying the PIP/PBP screen.

Get NEC NP-PA622U PDF manuals and user guides View all NEC NP-PA622U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 142 highlights

Connecting an External Monitor HDMI OUT 6. Installation and Connections AUDIO OUT HDMI cable (not supplied) Stereo mini-plug audio cable (not supplied) HDMI IN AUDIO IN Computer cable (VGA) (not supplied) You can connect a separate, external monitor to your projector to simultaneously view on a monitor the computer analog image you're projecting. • BNC(CV) component video signals and BNC(Y/C) S-video signals will not be output. • Please refer to Page 85 when displaying the PIP/PBP screen. NOTE: • When outputting HDMI signals, turn on the power of the video device on the output side and keep it connected before inputting video signals into this device. The HDMI output terminals of the projector are equipped with repeater functions. When a device is connected to the HDMI output terminal, the resolution of the output signal is limited by the resolution supported by the connected device. • When the [STANDBY MODE] of this device is set to [NORMAL], HDMI signals will not be output. To output HDMI signals, set the [STANDBY MODE] to [HDBaseT STANDBY], turn on the power supply of the transmission device and keep it connected. • In the case of the HDMI output terminal of the projector, the theoretical number of units that can be connected in a series is seven. The maximum number of units that can be connected may be reduced by the external environment and quality of the signal and cable, etc. The number of units that can be connected may differ depending on the HDCP version, restriction on the number of HDCP repeaters in the source device and the quality of the cable. The overall system needs to be checked in advance when building a system. • When audio equipment is connected, the projector speaker is disabled. • To output audio from the audio output terminal when the input terminal is neither "COMPUTER IN" nor "BNC IN", select [BNC] under [AUDIO SELECT] of the on-screen menu. • When the [STANDBY MODE] is set to [NORMAL], video and audio will not be output if the projector goes into the standby mode. Set the mode to [HDBaseT STANDBY], turn on the power of the transmission device and keep it in a connected state. 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
129
6. Installation and Connections
HDMI IN
AUDIO IN
HDMI OUT
AUDIO OUT
Connecting an External Monitor
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the computer
analog image you’re projecting.
• BNC(CV) component video signals and BNC(Y/C) S-video signals will not be output.
• Please refer to Page
85
when displaying the PIP/PBP screen.
NOTE:
• When outputting HDMI signals, turn on the power of the video device on the output side and keep it connected before inputting
video signals into this device. The HDMI output terminals of the projector are equipped with repeater functions. When a device is
connected to the HDMI output terminal, the resolution of the output signal is limited by the resolution supported by the connected
device.
• When the [STANDBY MODE] of this device is set to [NORMAL], HDMI signals will not be output. To output HDMI signals, set the
[STANDBY MODE] to [HDBaseT STANDBY], turn on the power supply of the transmission device and keep it connected.
• In the case of the HDMI output terminal of the projector, the theoretical number of units that can be connected in a series is seven.
The maximum number of units that can be connected may be reduced by the external environment and quality of the signal and
cable, etc. The number of units that can be connected may differ depending on the HDCP version, restriction on the number of
HDCP repeaters in the source device and the quality of the cable. The overall system needs to be checked in advance when build
-
ing a system.
• When audio equipment is connected, the projector speaker is disabled.
• To output audio from the audio output terminal when the input terminal is neither “COMPUTER IN” nor “BNC IN”, select [BNC]
under [AUDIO SELECT] of the on-screen menu.
• When the [STANDBY MODE] is set to [NORMAL], video and audio will not be output if the projector goes into the standby mode.
Set the mode to [HDBaseT STANDBY], turn on the power of the transmission device and keep it in a connected state.
Computer cable (VGA) (not supplied)
Stereo mini-plug audio cable
(not supplied)
HDMI cable (not supplied)