Nikon COOLPIX 4200 User Manual - Page 143

Troubleshooting

Page 143 highlights

Troubleshooting If your camera fails to function as expected, check the list of common problems below before consulting your retailer or Nikon representative. Refer to the page numbers listed in the right-most column for information on solving the problems listed here. Electronically-Controlled Cameras In extremely rare instances, unusual characters may appear in the monitor and the camera may stop functioning. In most cases, this phenomenon is caused by a strong external static charge. Turn the camera off, remove and replace the battery, and turn the camera on again, or, if you are using an AC adapter kit (optional), disconnect and reconnect the adapter, and turn the camera on again. Note that disconnecting the power source as described above may result in the loss of any data not recorded to the memory or memory card at the time the problem occurred. Data already recorded to the memory or memory card will not be affected. Problem Possible cause • Camera is off. 12 • Monitor is off. 5 • Battery is not correctly inserted or battery-chamber cover 8 is not properly latched. • Battery is exhausted. 12 Monitor is blank • Optional EH-62A AC adapter kit is not properly con- 124 nected. • Camera is in standby mode. Press shutter-release button 13 halfway. • USB cable is connected. 62 • Audio/video cable is connected. 59 Camera turns off • Battery is low. 12 without warning • Battery is cold. 128 No indicators appear in moni- tor • Indicators may be hidden. Change Monitor settings in setup menu. 115 Monitor is hard to read • Ambient lighting is too bright: move to a darker location. • Monitor brightness needs adjustment. • Monitor is dirty: clean monitor. 127 117 127 Technical Notes 133

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152

133
Technical Notes
Troubleshooting
If your camera fails to function as expected, check the list of common prob-
lems below before consulting your retailer or Nikon representative. Refer to
the page numbers listed in the right-most column for information on solving
the problems listed here.
Electronically-Controlled Cameras
In extremely rare instances, unusual characters may appear in the monitor and the
camera may stop functioning. In most cases, this phenomenon is caused by a strong
external static charge. Turn the camera off, remove and replace the battery, and turn
the camera on again, or, if you are using an AC adapter kit (optional), disconnect and
reconnect the adapter, and turn the camera on again. Note that disconnecting the
power source as described above may result in the loss of any data not recorded to
the memory or memory card at the time the problem occurred. Data already recorded
to the memory or memory card will not be affected.
Problem
Possible cause
Monitor is blank
Camera is off.
Monitor is off.
Battery is not correctly inserted or battery-chamber cover
is not properly latched.
Battery is exhausted.
Optional EH-62A AC adapter kit is not properly con-
nected.
Camera is in standby mode. Press shutter-release button
halfway.
USB cable is connected.
Audio/video cable is connected.
12
5
8
12
124
13
62
59
Camera turns off
without warning
Battery is low.
Battery is cold.
12
128
No indicators
appear in moni-
tor
Indicators may be hidden. Change
Monitor settings
in
setup menu.
115
Monitor is hard
to read
Ambient lighting is too bright: move to a darker location.
Monitor brightness needs adjustment.
Monitor is dirty: clean monitor.
127
117
127