Onkyo PR-SC5508 Owner Manual - Page 64

Re-EQ With the Re-EQ function, you can compensate a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing. ■ Re-EQ ` Off: Re-EQ Function off. ` On: Re-EQ Function on. This function can be used with the following listening modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Multichannel, DTS, DTS-HD High Resolution Audio, DTS-HD Master Audio, DTS Express, DSD, Dolby EX, Dolby Pro Logic IIz Height, Dolby PLIIx Movie, Neo:6 Cinema and 5.1-channel source + Neo:6, and Neural Surround. ■ Re-EQ(THX) ` Off: Re-EQ (THX) Function off. ` On: Re-EQ (THX) Function on. This function can be used with the following listening modes: THX Cinema, THX Surround EX, and THX Ultra2 Cinema. Note • Settings for the Re-EQ function are kept in each listening mode. However, in THX listening mode, when the AV controller is turned off, it will return to "On". • This setting cannot be used while a pair of headphones is connected. Audio Selector You can set priorities of audio output when there are both digital and analog inputs. ■ Audio Selector ` ARC: The audio signal from your TV tuner can be sent to the HDMI OUT MAIN of the AV controller.*1 With this selection the TV's audio can be automatically selected as a priority among other assignments. ` HDMI: This can be selected when HDMI IN has been assigned as an input source. If both HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) have been assigned, HDMI input is automatically selected as a priority. ` COAX: This can be selected when COAXIAL IN has been assigned as an input source. If both coaxial and HDMI inputs have been assigned, coaxial input is automatically selected as a priority. ` OPT: This can be selected when OPTICAL IN has been assigned as an input source. If both optical and HDMI inputs have been assigned, optical input is automatically selected as a priority. En 64 ` Multich: The AV controller always outputs analog signals from multichannel analog input. ` Balance: The AV controller always outputs analog signals from balanced input. ` Analog: The AV controller always outputs analog signals. Note • The setting is stored individually for each input selector. • This setting can be made only for the input source that is assigned as HDMI IN, COAXIAL IN, or OPTICAL IN. • To select the digital audio input, see "Digital Audio Input" for more detail (➔ 47). • To select "Multich", you must assign the multichannel input (➔ 47). • To select "Balance", you must assign the balanced input (➔ 47). *1 You can select "ARC" if you select the TV/CD input selector. But you cannot select it if you've selected "Off" in the "Audio Return Channel" setting (➔ 61). Setting the Incoming Digital Signal (Fixed Mode) By pressing ENTER while selecting "HDMI", "COAX", "OPT" in the "Audio Selector", you can specify the input signal in the Fixed Mode. Pressing ENTER again allows you to return to the "Audio Selector" setting. Normally, the AV controller detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS. • If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM. • If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS. ■ Fixed Mode ` Auto: The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead. ` PCM: Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced. ` DTS: Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. Note • The setting is stored individually for each input selector. • The setting will be reset to "Auto" when you change the setting in the "Audio Selector" (➔ 64).