Panasonic KX-WP1050 Wifi Telephone - Page 161

Enable Except Ident Packets], Stateful Packet

Page 161 highlights

Base Unit Settings 3 Configure the settings, then click [Save]. Setting [Transmission/ reception of Packets with private IP addresses via WAN interface] [Stateful Packet Inspection] [Attack Detection] Description L Select whether to deny or allow packets to be sent or received when the source of an incoming (from WAN) packet and the destination of an outgoing (to WAN) packet are private IP addresses. This feature is valid when the WAN IP address is global. The default is set to Deny. L Check whether output or not this log. The default is set to ON. L Select whether to enable or disable the stateful packet inspection feature. L Some E-mail servers authenticate clients using identification packets which use TCP port 113. If the E-mail feature does not work well, select [Enable (Except Ident Packets)], which is the default setting for this feature. L Check whether output or not this log. The default is set to ON. L Select whether to enable or disable the attack detection feature. The default is set to Disable. L The following type of attacks can be detected: - TCP Scan - UDP Scan - ICMP Echo L Check whether output or not this log. The default is set to OFF. L Check the box in the Log Output column to create a log of each action. L If you select [Enable] and check "Log Output", the log will be output. If you select [Disable], the log will not be output even if you check "Log Output". 4 Click [Restart]. L The base unit automatically restarts and the Top Menu is displayed. Note: L This feature is not available in AP (Bridge) mode. For assistance, please visit http://www.panasonic.com/help 161

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236

Base Unit Settings
For assistance, please visit http://www.panasonic.com/help
161
3
Configure the settings, then click
[Save]
.
L
Check the box in the Log Output column to create a log of each action.
L
If you select
[Enable]
and check “Log Output”, the log will be output. If you select
[Disable]
, the log will not be output even if you check “Log Output”.
4
Click
[Restart]
.
L
The base unit automatically restarts and the Top Menu is displayed.
Note:
L
This feature is not available in AP (Bridge) mode.
Setting
Description
[Transmission/
reception of
Packets with
private IP
addresses via
WAN interface]
L
Select whether to deny or allow packets to be sent or
received when the source of an incoming (from WAN) packet
and the destination of an outgoing (to WAN) packet are
private IP addresses. This feature is valid when the WAN IP
address is global. The default is set to Deny.
L
Check whether output or not this log. The default is set to ON.
[Stateful Packet
Inspection]
L
Select whether to enable or disable the stateful packet
inspection feature.
L
Some E-mail servers authenticate clients using identification
packets which use TCP port 113. If the E-mail feature does
not work well, select
[Enable (Except Ident Packets)]
,
which is the default setting for this feature.
L
Check whether output or not this log. The default is set to ON.
[Attack Detection]
L
Select whether to enable or disable the attack detection
feature. The default is set to Disable.
L
The following type of attacks can be detected:
TCP Scan
– UDP Scan
ICMP Echo
L
Check whether output or not this log. The default is set to
OFF.