Home » Samsung Manuals » Laser Printers » Samsung ML 3051N » Manual Viewer

Samsung ML 3051N User Manual (ENGLISH) - Page 26

Static addressing, Dynamic addressing (BOOTP/DHCP), Configuring EtherTalk, Configuring IPX frame types - printer manual

UPC - 635753624243

Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Static addressing To enter a TCP/IP address from your printer's control panel, take the following step: 1 Press Menu until Network appears on the bottom line of the display and press OK. 2 Press OK when TCP/IP appears. 3 Press the Scroll buttons until Static appears and press OK. 4 Press OK when IP Address appears. 5 Set the first byte between 0 and 255 using the Scroll buttons and press OK to move to the next byte. Repeat this to complete the address from the 1st byte to the 4th byte. 6 When you have finished, press OK. 7 Repeat step 5 and 6 to configure the other TCP/IP parameters: subnet mask and gateway address. 8 Press Stop to return to Standby mode. Dynamic addressing (BOOTP/DHCP) To have a TCP/IP address assigned automatically by the server, take the following step: 1 Press Menu until Network appears on the bottom line of the display. 2 Press OK when TCP/IP appears. 3 Press the Scroll buttons until DHCP or BOOTP appears and press OK. 4 Press Stop to return to Standby mode. Configuring EtherTalk EtherTalk is AppleTalk used in an Ethernet network. This protocol is widely used in Macintosh network environments. To use EtherTalk, take the following step: 1 Press Menu until Network appears on the bottom line of the display and press OK. 2 Press the Scroll buttons until EtherTalk appears and press OK. 3 Press the Scroll buttons until On appears and press OK. 4 Press Stop to return to Standby mode. Configuring IPX frame types To use IPX/SPX protocol networks (for example, Novell NetWare), the format of the network communication frames must be specified for the printer. In most cases, you can keep the Auto setting. However, you can manually set the frame type format, if required. Take the following step to change the frame type format: 1 Press Menu until Network on the bottom line of the display and press OK. 2 Press the Scroll buttons until NetWare appears and press OK. 3 Press the Scroll buttons until the desired frame type appears. • Auto: Automatically senses and limits the frame type to the first one detected. • 802.2: Limits the frame type to IPX over IEEE 802.2 with IEEE 802.3 frames. All others will be discarded. • 802.3: Limits the frame type to IPX over IEEE 802.3 frames. All others will be discarded. • Ethernet II: Limits the frame type to IPX over Ethernet Frames. All others will be discarded. • SNAP: Limits the frame type to IPX over SNAP with IEEE 802.3 frames. All others will be discarded. • Off: The IPX/SPX protocol is disabled. 4 Press OK to save the selection. 5 Press Stop to return to Standby mode. 4.2

Section	Page
Contents	5
Introduction	11
Special features	11
Printer overview	12
Front view	12
Rear view	13
Control panel overview	13
Finding more information	14
Selecting a location	14
System setup	15
Using control panel menus (ML-3051N, ML-3051ND only)	15
Accessing control panel menus	15
Menu overview	15
Information menu	16
Layout menu	16
Paper menu	17
Graphic menu	17
System Setup menu	18
Emulation menu	18
Network menu	20
Printing a demo page	20
Changing the display language (ML-3051N, ML- 3051ND only)	20
Using toner save mode	21
Using the control panel button	21
From the software application	21
Software overview	22
Supplied software	22
Printer driver features	23
System requirements	23
Network setup	25
Introduction	25
Via network administration programs	25
Via the control panel	25
Supported operating systems	25
Configuring TCP/IP	25
Static addressing	26
Dynamic addressing (BOOTP/DHCP)	26
Configuring EtherTalk	26
Configuring IPX frame types	26
Setting Ethernet speed	27
Restoring the network configuration	27
Printing a network configuration page	27
Loading print media	28
Selecting print media	28
Supported sizes of paper	29
Guidelines for selecting and storing print media	30
Loading paper	31
Using the tray 1 or the optional tray 2	32
Changing the size of the paper in the tray 1	32
Using the multi-purpose tray	33
Using manual feed mode	34
Selecting an output location	35
Printing to the output tray (Face down)	35
Printing to the rear cover (Face up)	35
Basic printing	36
Printing a document	36
Canceling a print job	36
Ordering supplies and accessories	37
Toner cartridges	37
Accessories	37
How to purchase	37
Maintenance	38
Printing information page	38
Cleaning the printer	38
Cleaning the outside of the printer	38
Cleaning the inside of the printer	38
Maintaining the toner cartridge	39
Checking the remaining toner (ML-3051N, ML-3051ND only)	39
Redistributing toner cartridge	40
Replacing the toner cartridge	40
Clearing the Toner Low Replace Toner message	41
Maintenance parts	41
Troubleshooting	42
Clearing paper jams	42
In the paper feed area	42
Around the toner cartridge	44
In the paper exit area	44
In the duplex unit area (ML-3051ND only)	45
Tips for avoiding paper jams	46
Troubleshooting checklist	47
Understanding the Status LED	47
Understanding display messages	48
Toner cartridge-related messages	49
Solving general printing problems	50
Solving print quality problems	52
Common Windows problems	54
Common PostScript problems	54
Common Linux problems	55
Common Macintosh problems	55
Installing accessories	56
Precautions when installing accessories	56
Installing a memory DIMM	56
Setting the memory in the PostScript printer properties	57
Installing a wireless network interface card	57
Configuring the wireless network parameters	58
Specifications	60
Printer specifications	60
Index	61
Software section	63
Software section Contents	64
Installing Printer Software in Windows	67
Installing Printer Software	67
Installing Software for Local Printing	67
Installing Software for Network Printing	70
Reinstalling Printer Software	73
Removing Printer Software	74
Basic Printing	75
Printing a Document	75
Printer Settings	76
Layout Tab	76
Paper Tab	77
Graphics Tab	78
Extras Tab	79
About Tab	79
Printer Tab	79
Using a Favorite Setting	80
Using Help	80
Advanced Printing	81
Printing Multiple Pages on One Sheet of Paper (N-Up Printing)	81
Printing Posters	82
Printing Booklets	82
Printing on Both Sides of Paper	83
Printing a Reduced or Enlarged Document	83
Fitting Your Document to a Selected Paper Size	83
Using Watermarks	84
Using an Existing Watermark	84
Creating a Watermark	84
Editing a Watermark	84
Deleting a Watermark	84
Using Overlays	85
What is an Overlay?	85
Creating a New Page Overlay	85
Using a Page Overlay	85
Deleting a Page Overlay	85
Using Windows PostScript Driver	86
Printer Settings	86
Advanced	86
Using Help	86
Sharing the Printer Locally	87
Setting Up a Host Computer	87
Setting Up a Client Computer	87
Using Smart Panel	88
Understanding Smart Panel	88
Opening the Troubleshooting Guide	89
Using Printer Settings Utility	89
Using Onscreen Help File	89
Changing the Smart Panel Program Settings	89
Using Your Printer in Linux	90
Getting Started	90
Installing the Unified Linux Driver	90
Installing the Unified Linux Driver	90
Uninstalling the Unified Linux Driver	91
Using the Unified Driver Configurator	91
Opening the Unified Driver Configurator	91
Printers Configuration	92
Ports Configuration	92
Configuring Printer Properties	93
Printing a Document	93
Printing from Applications	93
Printing Files	94
Using Your Printer with a Macintosh	95
Installing printer driver for Macintosh	95
ML-3050 only	95
ML-3051N/ML-3050ND only	95
Setting Up the Printer	96
ML-3050 only	96
ML-3051N/ML-3050ND only	96
Printing	97
Printing a Document	97
Changing Printer Settings	97
Printing Multiple Pages on One Sheet of Paper	98
Duplex Printing	99

Match case Limit results 1 per page

Network setup>

Static addressing

To enter a TCP/IP address from your printer’s control panel, take the

following step:

Press

until

Network

appears on the bottom line of the

display and press

Press

when

TCP/IP

appears.

Press the

Scroll

buttons until

Static

appears and press

Press

when

IP Address

appears.

Set the first byte between 0 and 255 using the

Scroll

buttons and

press

to move to the next byte.

Repeat this to complete the address from the 1st byte to the 4th

byte.

When you have finished, press

Repeat step 5 and 6 to configure the other TCP/IP parameters:

subnet mask and gateway address.

Press

Stop

to return to Standby mode.

Dynamic addressing (BOOTP/DHCP)

To have a TCP/IP address assigned automatically by the server, take the

following step:

Press

until

Network

appears on the bottom line of the

display.

Press

when

TCP/IP

appears.

Press the

Scroll

buttons until

DHCP

BOOTP

appears and press

Press

Stop

to return to Standby mode.

Configuring EtherTalk

EtherTalk is AppleTalk used in an Ethernet network. This protocol is

widely used in Macintosh network environments. To use EtherTalk, take

the following step:

Press

until

Network

appears on the bottom line of the

display and press

Press the

Scroll

buttons until

EtherTalk

appears and press

Press the

Scroll

buttons until

appears and press

Press

Stop

to return to Standby mode.

Configuring IPX frame types

To use IPX/SPX protocol networks (for example, Novell NetWare), the

format of the network communication frames must be specified for the

printer. In most cases, you can keep the

Auto

setting. However, you can

manually set the frame type format, if required. Take the following step

to change the frame type format:

Press

until

Network

on the bottom line of the display and

press

Press the

Scroll

buttons until

NetWare

appears and press

Press the

Scroll

buttons until the desired frame type appears.

•

Auto

: Automatically senses and limits the frame type to the first

one detected.

•

802.2

: Limits the frame type to IPX over IEEE 802.2 with IEEE

802.3 frames. All others will be discarded.

•

802.3

: Limits the frame type to IPX over IEEE 802.3 frames. All

others will be discarded.

•

Ethernet II

: Limits the frame type to IPX over Ethernet Frames. All

others will be discarded.

•

SNAP

: Limits the frame type to IPX over SNAP with IEEE 802.3

frames. All others will be discarded.

•

Off

: The IPX/SPX protocol is disabled.

Press

to save the selection.

Press

Stop

to return to Standby mode.