Samsung ML 3051N User Manual (ENGLISH) - Page 48

Understanding display messages, LSU Hsync Error - sleep mode problems

Get Samsung ML 3051N - B/W Laser Printer PDF manuals and user guides
UPC - 635753624243
View all Samsung ML 3051N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Understanding display messages Messages appear on the Smart Panel program window or the control panel display to indicate the printer's status or errors. Refer to the tables below to understand the messages' meaning and correct the problem if necessary. Messages and their meanings are listed in alphabetical order. Note When you call for service, it is very convenient to tell the service representative the display message. Message Meaning Suggested solutions Door Open The front cover or rear cover is not securely latched. Close the cover until it locks into place. Duplex Jam 0 Check Inside Paper has jammed during duplex printing. Clear the jam. See page 9.4. Duplex Jam 1 Open/ Close Door Paper has jammed during duplex printing. Clear the jam. See page 9.5. Fuser Door Open Load Manually Press Stop Key The fuser door is not securely latched. The multi-purpose tray is empty in manual feed mode. Open the rear cover and close the fuser door until it locks into place. For the location of the fuser door, see page 9.4. Load a sheet of print material and press Stop. Low Heat Error Cycle Power There is a problem in the fuser unit. Unplug the power cord and plug it back in. If the problem persists, please call for service. LSU Hsync Error Cycle Power A problem has occurred in the LSU (Laser Scanning Unit). Unplug the power cord and plug it back inches. If the problem persists, please call for service. LSU Motor Error Cycle Power A problem has occurred in the LSU (Laser Scanning Unit). Unplug the power cord and plug it back inches. If the problem persists, please call for service. Message Meaning Suggested solutions Main Motor Locked There is a problem in the main motor. Open and then close the front cover. Open Heat Error Cycle Power There is a problem in the fuser unit. Unplug the power cord and plug it back in. If the problem persists, please call for service. Over Heat Error Cycle Power There is a problem in the fuser unit. Unplug the power cord and plug it back in. If the problem persists, please call for service. Paper Jam 0 Open/Close Door Paper has jammed in the feeding area of the tray. Clear the jam. See page 9.1 and page 9.1. Paper Jam 1 Open/Close Door Paper has jammed in the fuser area. Clear the jam. See page 9.3. Paper Jam 2 Check Inside Printing... Ready Paper has jammed in the paper exit area. The printer is printing jobs using the displayed language. The printer is on-line and ready to printer. Clear the jam. See page 9.3. Complete your printing. Use your printer. Self Diagnostic... Sleeping... The engine in your printer is checking some problems detected. The printer is on power save mode. Please wait a few minutes. When data is received, it switches to on-line automatically. Tray 1 Paper Empty There is no paper in Load paper in the the tray 1. tray 1. See page 5.5. Tray 2 Paper Empty There is no paper in the optional tray 2. Load paper in the optional tray 2. See page 5.5. 9.7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
9
.7
<
Troubleshooting>
Understanding display messages
Messages appear on the Smart Panel program window or the control
panel display to indicate the printer’s status or errors. Refer to the tables
below to understand the messages’ meaning and correct the problem if
necessary. Messages and their meanings are listed in alphabetical
order.
Note
When you call for service, it is very convenient to tell the
service representative the display message.
Message
Meaning
Suggested solutions
Door Open
The
front cover
or
rear cover
is not
securely latched.
Close the cover until
it locks into place.
Duplex Jam 0
Check Inside
Paper has jammed
during duplex
printing.
Clear the jam. See
page 9.4.
Duplex Jam 1
Open/
Close Door
Paper has jammed
during duplex
printing.
Clear the jam. See
page 9.5.
Fuser Door Open
The
fuser door
is
not securely latched.
Open the
rear cover
and close the
fuser
door
until it locks into
place.
For the location of
the
fuser door
, see
page 9.4.
Load Manually
Press Stop Key
The
multi-purpose
tray
is empty in
manual feed mode.
Load a sheet of print
material and press
Stop
.
Low Heat Error
Cycle Power
There is a problem
in the fuser unit.
Unplug the
power
cord
and plug it back
in. If the problem
persists, please call
for service.
LSU Hsync Error
Cycle Power
A problem has
occurred in the LSU
(Laser Scanning
Unit).
Unplug the
power
cord
and plug it back
inches. If the
problem persists,
please call for
service.
LSU Motor Error
Cycle Power
A problem has
occurred in the LSU
(Laser Scanning
Unit).
Unplug the
power
cord
and plug it back
inches. If the
problem persists,
please call for
service.
Main Motor Locked
There is a problem
in the main motor.
Open and then close
the
front cover
.
Open Heat Error
Cycle Power
There is a problem
in the fuser unit.
Unplug the
power
cord
and plug it back
in. If the problem
persists, please call
for service.
Over Heat Error
Cycle Power
There is a problem
in the fuser unit.
Unplug the
power
cord
and plug it back
in. If the problem
persists, please call
for service.
Paper Jam 0
Open/Close Door
Paper has jammed
in the feeding area
of the tray.
Clear the jam. See
page 9.1 and
page 9.1.
Paper Jam 1
Open/Close Door
Paper has jammed
in the fuser area.
Clear the jam. See
page 9.3.
Paper Jam 2
Check Inside
Paper has jammed
in the paper exit
area.
Clear the jam. See
page 9.3.
Printing...
The printer is
printing jobs using
the displayed
language.
Complete your
printing.
Ready
The printer is on-line
and ready to printer.
Use your printer.
Self Diagnostic...
The engine in your
printer is checking
some problems
detected.
Please wait a few
minutes.
Sleeping...
The printer is on
power save mode.
When data is
received, it switches
to on-line
automatically.
Tray 1
Paper Empty
There is no paper in
the
tray 1
.
Load paper in the
tray 1
. See page 5.5.
Tray 2
Paper Empty
There is no paper in
the
optional tray 2
.
Load paper in the
optional tray 2
. See
page 5.5.
Message
Meaning
Suggested solutions