Sharp DT 400 DT-400 Operation Manual - Page 57

Removing and Installing the Lamp Unit

Get Sharp DT 400 - HDTV- DLP Projector PDF manuals and user guides
UPC - 074000364332
View all Sharp DT 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Removing and Installing the Lamp Unit Warning! • During projector operation, the lamp unit is very hot. Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury. Info • Ensure to remove the lamp unit using the handle. Ensure not to touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, ensure to carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit. 1 Press on the projector or on the remote control to put the projector into standby mode. • Wait until the cooling fan stops. 2 Disconnect the power cord. • Unplug the power cord from the AC socket. • Leave the lamp until it has fully cooled down (about 1 hour). 3 Remove the lamp unit cover. • Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Hold the tab and slide towards the direction of the arrow to remove the lamp unit cover (2). Optional accessory Lamp unit AN-K2LP STANDBY button AC socket 1 2 Tab User service screw (for lamp unit cover) Tab Appendix -57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
Appendix
-57
Info
•
Ensure to remove the lamp unit using the
handle. Ensure not to touch the glass sur-
face of the lamp unit or the inside of the
projector.
•
To avoid injury to yourself and damage to
the lamp, ensure to carefully follow the
steps below.
•
Do not loosen other screws except for the
lamp unit cover and lamp unit.
1
Press
on the projector or
on the remote control to put
the projector into standby mode.
•
Wait until the cooling fan stops.
2
Disconnect the power cord.
•
Unplug the power cord from the AC
socket.
•
Leave the lamp until it has fully cooled
down (about 1 hour).
3
Remove the lamp unit cover.
•
Turn the projector over. Loosen the user
service screw (
1
) that secures the lamp
unit cover. Hold the tab and slide to-
wards the direction of the arrow to re-
move the lamp unit cover (
2
).
AC socket
STANDBY button
1
2
User service screw
(for lamp unit cover)
Tab
Tab
Removing and Installing the Lamp Unit
Optional
accessory
Lamp unit
AN-K2LP
Warning!
•
During projector operation, the lamp unit is very hot. Do not remove the lamp unit from the projector
right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury.