Sharp DT 400 DT-400 Operation Manual - Page 62
Specifications - dlp projector
![]() |
UPC - 074000364332
View all Sharp DT 400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 62 highlights
Specifications Product type Projector Model DT-400 Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43 DTV 480I/480P/720P/1080I Display method Single Panel Digital Micromirror Device (DMD™) by Texas Instruments DLP panel Panel size: 0.8" Drive method: Digital Light Processing (DLP™) No. of dots: 921,600 dots (1,280 [H] ן720 [V]) Lens 1-1.5 ןzoom lens, F2.0-2.5 f=21.3-31.6 mm Projection lamp 275 W DC lamp Video input signal RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω terminated S-video input signal 4-pin Mini DIN connector (INPUT 3) Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated Component input signal RCA Connector (INPUT 1, 2) Y: 1.0 Vp-p, sync negative, 75 Ω terminated PB (CB): 0.7 Vp-p, 75 Ω terminated PR (CR): 0.7 Vp-p, 75 Ω terminated Analog RGB/Digital 29-pin DVI-I terminal (INPUT 5/DIGITAL) Input impedance 50 Ω Input level 250-1000 mV Input impedance 75 Ω Input level 0.7 Vp-p Y: 1.0 Vp-p, sync negative, 75 Ω terminated PB (CB): 0.7 Vp-p, 75 Ω terminated PR (CR): 0.7 Vp-p, 75 Ω terminated • Separate sync/Composite sync Input level TTL level Input impedance 1 KΩ • Green on sync Input level (Synchronizing input) 0.286 Vp-p Input impedance 75 Ω Horizontal resolution 720 TV lines (DTV 720P input) Pixel clock 12-80 MHz Vertical frequency 43-75 Hz Horizontal frequency 15-70 kHz Rated voltage AC 100-240 V Input current 3.65 A (When using AC 100 V) Rated frequency 50/60 Hz Power consumption 360 W (When using AC 100 V) Power consumption (standby) 6 W (When using AC 100 V) Heat dissipation 1,350 BTU/hour Operating temperature 41°F to 95°F (ם5°C to ם35°C) Storage temperature מ4°F to 140°F (מ20°C to ם60°C) Cabinet Plastic I/R carrier frequency 38 kHz Dimensions (approx.) 12 7/32" × 3 33/64" × 11 7/64" (310 (W) × 89 (H) × 282 (D) mm) Weight (approx.) 9.5 lbs. (4.3 kg) Supplied accessories Remote control, Two AA size batteries, Power cord, Lens cap (attached on the body), Operation manual Replacement parts Lamp unit (Lamp/cage module) (AN-K2LP), Remote control (RRMCGA334WJSA), AA size batteries, Power cord (QACCDA007WJPZ), Lens cap (PCAPHA021WJSA), Operation manual (TINS-B532WJZZ) As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. -62
![](/manual_guide/products/sharp-dt-400-dt400-operation-manual-63c4da1/62.png)