Sharp PG-M25X PGM25X Operation Manual - Page 23

Calibrating the, GyroRemote

Get Sharp PG-M25X - Notevision XGA DLP Projector PDF manuals and user guides View all Sharp PG-M25X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Introduction Calibrating the GyroRemote If there are any extreme temperature changes when the GyroRemote is being used or after batteries have been replaced, the mouse cursor or pointer may continue to move by itself even if no action has been performed. In this case, calibrate the GyroRemote using the following procedure. 1 Double click on the rear of the GyroRemote. 2 Make sure that the LED indicator is lit, and place the GyroRemote on a leveled location. • After leaving the GyroRemote for 6 seconds, the calibration of the GyroRemote is complete. 3 Press , after leaving the GyroRemote for more than 6 seconds. • Calibration is complete after the remote has been left for more than 6 seconds. GYRO ACTIVE button PG-M25X#E#p08_20_a.p65 19 02.4.29, 4:56 PM -19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Introduction
-19
Calibrating the
GyroRemote
If there are any extreme temperature changes
when the GyroRemote is being used or after
batteries have been replaced, the mouse
cursor or pointer may continue to move by
itself even if no action has been performed. In
this case, calibrate the GyroRemote using the
following procedure.
1
Double click
on the rear
of the GyroRemote.
2
Make sure that the LED
indicator is lit, and place the
GyroRemote on a leveled
location.
•
After leaving the GyroRemote for 6
seconds, the calibration of the
GyroRemote is complete.
3
Press
, after leaving the
GyroRemote for more than 6
seconds.
•
Calibration is complete after the
remote has been left for more than 6
seconds.
GYRO ACTIVE
button
PG-M25X#E#p08_20_a.p65
02.4.29, 4:56 PM
19