Home » Sony Manuals » Audio Components » Sony STR-DA4400ES » Manual Viewer

Sony STR-DA4400ES Operating Instructions (Large File - 23.37 MB) - Page 124

Programming the remote, To cancel programming

Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

Programming the remote You can customize the remote to match the components connected to your receiver. You can even program the remote to control nonSony components and also Sony components that the remote is normally unable to control. The procedure below uses as an example a case in which a VCR made by a company other than Sony is connected to the VIDEO 2 IN jacks on the receiver. RM SET UP SHIFT Numeric buttons AV ?/1 Input buttons ENT/ MEM 1 Press AV ?/1 while pressing RM SET UP. The RM SET UP button flashes. 2 While the RM SET UP button is flashing, press the input button (including TV) for the component you want to control. For example, if you are going to control a VCR connected to VIDEO 2 IN jack, press VIDEO 2. RM SET UP and the input button light up. If you press the button for a component of which you cannot program the remote, such as TUNER, PHONO, DMPORT or SOURCE, etc., the RM SET UP button keeps flashing. 3 Press the numeric buttons to enter the numeric code (or one of the codes if more than one code exists) corresponding to the component and the maker of the component you want to control. The input button lights up. Note For a TV remote code value, only numbers in the 500's are valid. 4 Press ENT/MEM or ENTER. Once the numeric code has been verified, the RM SET UP button flashes twice and the remote automatically exits the programming mode. The input button also turns off. To cancel programming Press RM SET UP during any step. The numeric codes corresponding to the component and the maker of the component Use the numeric codes in the tables below to control non-Sony components and also Sony components that the remote is normally unable to control. Since the remote signal that a component accepts differs depending on the model and year of the component, more than one numeric code may be assigned to a component. If you fail to program your remote using one of the codes, try using other codes. Notes • The numeric codes are based on the latest information available for each brand. There is a chance, however, that your component will not respond to some or all of the codes. • All of the input buttons on this remote may not be available when used with your particular component. 124GB

Section	Page
GB	2
Table of Contents	4
Getting Started	19
1: Installing speakers	19
2: Connecting speakers	21
3: Connecting the monitor	23
4a: Connecting the audio components	25
4b: Connecting the video components	30
5: Connecting the antennas (aerials)	39
6: Preparing the receiver and the remote	40
7: Displaying the GUI menu on the TV screen	41
8: Setting the speakers	42
9: Calibrating the appropriate speaker settings automatically (Auto Calibration)	44
Guide to on-screen display operation	51
Playback	53
Enjoying sound/images from the component connected to the receiver	53
Enjoying sound/images from the components connected to the DIGITAL MEDIA PORT	55
Operating the TDM-iP1/ iP50/TDM-NC1 using the GUI menu of the receiver	56
Tuning	60
Listening to FM/AM radio	60
Presetting FM/AM radio stations	62
Listening to satellite radio	63
Connecting a satellite radio tuner	65
Preparing to listen to a satellite radio	65
Selecting a channel of the satellite radio	67
Presetting satellite radio channels	68
Restricting access to specific channels (Parental Lock) (SIRIUS only)	69
Enjoying Surround Sound	73
Playing back with 2-channel sound	73
Playing back with multi-channel surround	74
Enjoying a surround effect for music	77
Enjoying a surround effect for movies	79
Using Multi-zone Features	83
What you can do with the Multi-zone function	83
Making a multi-zone connection	84
Setting the speakers in zone 2	86
Switching the zone setting of the remote	87
Operating the receiver from another zone (ZONE 2/ZONE 3 operations)	87
Using Other Features	89
Using “BRAVIA” Sync features	89
Switching between digital and analog audio	92
Enjoying the sound/ images from other inputs (Input Assign)	93
Using the sleep timer	96
Enjoying the surround effect at low volume levels	96
Recording using the receiver	97
Switching the command mode of the receiver and the remote	99
Using a bi-amplifier connection	100
Adjusting Settings	102
Using the setting menu	102
Auto Calibration	103
Speaker settings	105
Surround settings	109
EQ settings	110
Multi Zone settings	111
Audio settings	112
Video settings	113
HDMI settings	115
System settings	116
Operating without connecting to a TV	116
Using the Remote	122
Operating each component using the remote	122
Programming the remote	124
Performing several commands in sequence automatically (Macro Play)	127
Setting remote commander codes that are not stored in the remote	129
Clearing all the contents of the remote’s memory	131
Additional Information	132
Glossary	132
Precautions	135
Troubleshooting	136
Specifications	141
Index	143
FR	146
Table des matières	148
Mise en service	166
1: Installation des enceintes	166
2: Raccordement des enceintes	168
3: Raccordement de l’écran	170
4a: Raccordement des appareils audio	172
4b: Raccordement des appareils vidéo	177
5: Raccordement des antennes	186
6: Préparation de l’ampli- tuner et de la télécommande	187
7: Affichage du menu GUI sur l’écran du téléviseur	188
8: Réglage des enceintes	189
9: Calibrage automatique aux réglages appropriés (Auto Calibration)	191
Guide pour les opérations à l’écran	198
Lecture	201
Écoute du son/visionnage d’images à partir de l’appareil raccordé à l’ampli-tuner	201
Écoute du son/visionnage d’images à partir des appareils raccordés au DIGITAL MEDIA PORT	203
Commande du TDM-iP1/ iP50/TDM-NC1 à l’aide du menu GUI de l’ampli- tuner	205
Sélection des stations	208
Écoute de stations de radio FM/AM	208
Préréglage des stations de radio FM/AM	210
Écouter la radio satellite	211
Raccorder un tuner radio satellite	213
Préparer la réception de la radio satellite	213
Sélectionner un canal de la radio satellite	215
Prérégler les canaux de la radio satellite	216
Restreindre l’accès à des canaux spécifiques (Parental Lock) (SIRIUS uniquement)	218
Écoute du son surround	222
Lecture avec un son 2 canaux	222
Lecture avec son surround multicanal	223
Écoute d’un effet surround pour de la musique	226
Écoute d’un effet surround pour des films	228
Utilisation des fonctionnalités multizone	232
Ce que vous pouvez faire avec la fonction multizone	232
Effectuer un raccordement multizone	233
Réglage des enceintes dans la zone 2	235
Changer le réglage de la zone de la télécommande	236
Commande de l’ampli- tuner depuis une autre zone (Commandes ZONE 2/ZONE 3)	236
Utilisation des autres fonctionnalités	238
Utilisation des fonctionnalités « BRAVIA » Sync	238
Passage entre son numérique et analogique	241
Écoute du son/visionnage d’images d’autres entrées (Input Assign)	242
Utilisation de la minuterie d’arrêt	245
Écoute du son surround à faible volume	245
Enregistrement à l’aide de l’ampli-tuner	246
Changement du mode de commande de l’ampli- tuner et de la télécommande	248
Utilisation d’un raccordement bi- amplificateur	249
Réglage des paramètres	251
Utilisation du menu de paramétrage	251
Auto Calibration	252
Paramètres Speaker	254
Paramètres Surround	258
Paramètres EQ	259
Paramètres Multi Zone	260
Paramètres Audio	262
Paramètres Video	263
Paramètres HDMI	265
Paramètres System	266
Utilisation sans raccordement à un téléviseur	266
Utilisation de la télécommande	272
Commande de chaque appareil à l’aide de la télécommande	272
Programmation de la télécommande	274
Exécution automatique d’une séquence de plusieurs commandes (Exécution de macro-commandes)	278
Mémorisation de codes de télécommande n’ayant pas été préprogrammés dans la télécommande	280
Effacement de tout le contenu de la mémoire de la télécommande	281
Informations complémentaires	282
Glossaire	282
Précautions	285
Guide de dépannage	286
Spécifications	291

Match case Limit results 1 per page

124

Programming the remote

You can customize the remote to match the

components connected to your receiver. You

can even program the remote to control non-

Sony components and also Sony components

that the remote is normally unable to control.

The procedure below uses as an example a

case in which a VCR made by a company other

than Sony is connected to the VIDEO 2 IN

jacks on the receiver.

Press AV

while pressing RM

SET UP.

The RM SET UP button flashes.

While the RM SET UP button is

flashing, press the input button

(including TV) for the

component you want to control.

For example, if you are going to control a

VCR connected to VIDEO 2 IN jack,

press VIDEO 2.

RM SET UP and the input button light up.

If you press the button for a component of

which you cannot program the remote,

such as TUNER, PHONO, DMPORT or

SOURCE, etc., the RM SET UP button

keeps flashing.

Press the numeric buttons to

enter the numeric code (or one

of the codes if more than one

code exists) corresponding to

the component and the maker

of the component you want to

control.

The input button lights up.

Note

For a TV remote code value, only numbers in

the 500’s are valid.

Press ENT/MEM or ENTER.

Once the numeric code has been verified,

the RM SET UP button flashes twice and

the remote automatically exits the

programming mode. The input button

also turns off.

To cancel programming

Press RM SET UP during any step.

Use the numeric codes in the tables below to

control non-Sony components and also Sony

components that the remote is normally unable

to control. Since the remote signal that a

component accepts differs depending on the

model and year of the component, more than

one numeric code may be assigned to a

component. If you fail to program your remote

using one of the codes, try using other codes.

Notes

• The numeric codes are based on the latest

information available for each brand. There is a

chance, however, that your component will not

respond to some or all of the codes.

• All of the input buttons on this remote may not be

available when used with your particular

component.

Numeric

buttons

RM SET

ENT/

MEM

SHIFT

Input

buttons

The numeric codes

corresponding to the component

and the maker of the component