Stihl MSE 210 C-BQ Instruction Manual - Page 29

wheel 4 slightly until the sprocket

Get Stihl MSE 210 C-BQ PDF manuals and user guides View all Stihl MSE 210 C-BQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

3 2 4 5 English 9931BA022 KN 181BA013 KN 1 N Fit the chain - start at the bar nose. Pay attention to the position of the tensioning gear and the cutting edges. N Turn the tensioning gear (1) clockwise as far as stop. N Turn the guide bar so that the tensioning gear is facing you. 181BA012 KN N Fit the chain over the sprocket (2). N Push the guide bar over the bar stud (3), the head of the rear bar stud must engage the slot. N Make sure the drive link tangs engage the bar groove (arrow) and then rotate the tensioning gear counterclockwise as far as stop. 9931BA020 KN When fitting the chain sprocket cover, check that the teeth of the tensioning gear and adjusting wheel mesh properly. N If necessary, turn the adjusting wheel (4) slightly until the sprocket cover can be pushed flush against the handle housing. N Pull the hinged handle (5) out until it engages in the upright position. N Fit the wingnut and tighten it moderately - finally tighten the wingnut by hand only after tensioning the saw chain. N Go to chapter on "Tensioning the Saw Chain" 9931BA021 KN N Place the chain sprocket cover in position and engage the guide lugs in the recesses in the handle housing. MSE 170 C, MSE 210 C 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
MSE 170 C, MSE 210 C
English
27
N
Fit the chain – start at the bar nose.
Pay attention to the position of the
tensioning gear and the cutting
edges.
N
Turn the tensioning gear (1)
clockwise as far as stop.
N
Turn the guide bar so that the
tensioning gear is facing you.
N
Fit the chain over the sprocket (2).
N
Push the guide bar over the bar
stud (3), the head of the rear bar
stud must engage the slot.
N
Make sure the drive link tangs
engage the bar groove (arrow) and
then rotate the tensioning gear
counterclockwise as far as stop.
N
Place the chain sprocket cover in
position and engage the guide lugs
in the recesses in the handle
housing.
When fitting the chain sprocket cover,
check that the teeth of the tensioning
gear and adjusting wheel mesh properly.
N
If necessary, turn the adjusting
wheel (4) slightly until the sprocket
cover can be pushed flush against
the handle housing.
N
Pull the hinged handle
(5) out until it
engages in the upright position.
N
Fit the wingnut and tighten it
moderately – finally tighten the
wingnut by hand only after
tensioning the saw chain.
N
Go to chapter on "Tensioning the
Saw Chain"
1
181BA012 KN
2
3
181BA013 KN
9931BA020 KN
9931BA021 KN
4
9931BA022 KN
5