Home » TP-Link Manuals » Wireless » TP-Link EAP115 » Manual Viewer

TP-Link EAP115 EAP115EU V1 User Guide - Page 44

MAC Filtering

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Here is the explanation of Figure 6-29: The policy name is Policy 1. Clients with IP address range 192.168.2.0/24 are able to visit IP range 10.10.10.0/24. Policy 1 is enabled. Click to edit the policy. Click to delete the policy. 6.3.3 MAC Filtering MAC Filtering uses MAC addresses to determine whether one host can access the wireless network or not. Thereby it can effectively control the user access in the wireless network. Figure 6-27 MAC Filtering Page  Settings Enable MAC Filtering: Check the box to enable MAC Filtering.  Station MAC Group Follow the steps below to add MAC groups. Step 1: Click , two tables will be shown. 36

Section	Page
Chapter 1 About This Guide	9
1.1 Intended Readers	9
1.2 Conventions	9
Chapter 2 Introduction	10
2.1 Overview of the EAP	10
2.2 Appearance Description	10
2.2.1 Top View	10
2.2.2 Panel Layout	11
2.2.3 Mounting Bracket	12
Chapter 3 Typical Topology	13
Chapter 4 Getting Started with the EAP	14
Option 1: Wireless Login	14
Option 2: Wired Login	15
Chapter 5 Management Mode	16
5.1 Mode Identification	16
5.2 Mode Switching	17
5.2.1 Choose the Work Mode the First Time You Login	17
5.2.2 Switch from Cluster to Standalone	18
5.2.3 Switch from Standalone to Cluster	18
Chapter 6 Cluster Mode	20
6.1 Quick Setup	20
6.2 Cluster	21
6.2.1 Cluster	21
6.2.2 AP List	21
6.3 Wireless	28
6.3.1 Wireless Settings	28
6.3.1.1 Wireless Basic Settings	29
6.3.1.2 SSIDs	29
6.3.1.3 Wireless Advanced Settings	34
6.3.1.4 Load Balance	34
6.3.2 Portal	35
6.3.2.1 Portal Configuration	36
6.3.2.2 Free Authentication Policy	42
6.3.3 MAC Filtering	44
6.3.4 Scheduler	46
6.3.5 QoS	49
6.3.5.1 AP EDCA Parameters	50
6.3.5.2 Station EDCA Parameters	51
6.3.6 Rogue AP Detection	52
6.3.6.1 Settings	53
6.3.6.2 Detected Rogue AP List	53
6.3.6.3 Trusted AP List	54
6.3.6.4 Download/Backup Trusted AP List	55
6.4 Monitoring	56
6.4.1 AP	56
6.4.1.1 AP List	56
6.4.2 SSID	60
6.4.2.1 SSID List	60
6.4.3 Client	61
6.4.3.1 User List	62
6.4.3.2 Portal Authenticated Guest	63
6.5 Management	64
6.5.1 System Log	64
6.5.1.1 Log List	64
6.5.1.2 Log Settings	65
6.5.2 Web Server	66
6.5.3 Management Access	67
6.5.4 LED ON/OFF	68
6.5.5 SSH	68
6.5.6 SNMP	69
6.6 System	72
6.6.1 User Account	72
6.6.2 Time Settings	72
6.6.2.1 Time Settings	73
6.6.2.2 Daylight Saving	74
6.6.3 Reboot/Reset	75
6.6.4 Backup & Restore	76
6.6.5 Firmware Upgrade	76
Chapter 7 Standalone Mode	78
7.1 Network	78
7.2 Wireless	79
7.2.1 Wireless Settings	80
7.2.1.1 Wireless Basic Settings	81
7.2.1.2 SSIDs	82
7.2.1.3 Wireless Advanced Settings	86
7.2.1.4 Load Balance	86
7.2.2 Portal	87
7.2.2.1 Portal Configuration	88
7.2.2.2 Free Authentication Policy	93
7.2.3 MAC Filtering	95
7.2.4 Scheduler	97
7.2.5 QoS	100
7.2.5.1 AP EDCA Parameters	101
7.2.5.2 Station EDCA Parameters	102
7.2.6 Rogue AP Detection	103
7.2.6.1 Settings	104
7.2.6.2 Detected Rogue AP List	104
7.2.6.3 Trusted AP List	105
7.2.6.4 Download/Backup Trusted AP List	106
7.3 Monitoring	107
7.3.1 AP	107
7.3.1.1 AP List	107
7.3.2 SSID	111
7.3.2.1 SSID List	111
7.3.3 Client	112
7.3.3.1 User List	113
7.3.3.2 Portal Authenticated Guest	114
7.4 Management	115
7.4.1 System Log	115
7.4.1.1 Log List	115
7.4.1.2 Log Settings	116
7.4.2 Web Server	117
7.4.3 Management Access	118
7.4.4 LED ON/OFF	119
7.4.5 SSH	119
7.4.6 SNMP	120
7.5 System	123
7.5.1 User Account	123
7.5.2 Time Settings	123
7.5.2.1 Time Settings	124
7.5.2.2 Daylight Saving	125
7.5.3 Reboot/Reset	126
7.5.4 Backup & Restore	127