Yamaha PSR-SX600 PSR-SX600 Owners Manual - Page 107

Troubleshooting

Get Yamaha PSR-SX600 PDF manuals and user guides View all Yamaha PSR-SX600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

Troubleshooting Overall A click or pop is heard when the power is turned on or off. The power is automatically turned off. Noise is heard from the instrument's speakers. Noise is heard from the instrument's speakers or headphones when using the instrument with the application on smart device. In the LCD, there are some specific points that are always lit or unlit. There is a slight difference in sound quality among different notes played on the keyboard. Some Voices have a looping sound. Some noise or vibrato is noticeable at higher pitches, depending upon the Voice. The overall volume is too low or no sound is heard. The sound is distorted or noisy. Not all simultaneously played notes sound. The keyboard volume is lower than the Song/Style playback volume. The Main display does not appear even when turning the power on. Some characters of the file/folder name are garbled. This is normal. Electrical current is being applied to the instrument. This is normal and due to the Auto Power Off function. If necessary, set the parameter of the Auto Power Off function (page 15). Noise may be heard if a mobile phone is used near the instrument or if the phone is ringing. Turn off the mobile phone, or use it further away from the instrument. When you use the instrument along with the application on your smart device, we recommend that you set "Airplane Mode" to "ON" on your smart device in order to avoid noise caused by communication. These are the result of defective pixels and occasionally occur in TFT-LCDs; they do not indicate a problem in operation. This is normal and is a result of the instrument's sampling system. The master volume may be set too low. Set it to an appropriate level with the [MASTER VOLUME] dial. All keyboard parts are set to off. Use the PART ON/OFF [RIGHT 1]/ [RIGHT 2]/[LEFT] button to turn it on. The volume of the individual parts may be set too low. Raise the volume in the Balance display (page 56). Make sure the desired channel is set to On (pages 54, 65). Headphones are connected, disabling the speaker output. Unplug the headphones. Make sure that the Speaker setting is set to On: [MENU] → Menu2 → Utility → [ENTER] → Config1. The [FADE IN/OUT] button is on, muting the sound. Press the [FADE IN/OUT] button to turn the function off. The volume may be turned up too high. Make sure all relevant volume settings are appropriate. This may be caused by certain effects or filter settings. Check the effect or filter settings and change them accordingly, referring to the Reference Manual. You are probably exceeding the maximum polyphony (page 110) of the instrument. When the maximum polyphony is exceeded, the earliest played notes will stop sounding, letting the latest played notes sound. The volume of the keyboard parts may be set too low. Raise the volume in the Balance display (page 56). This may occur if a USB flash drive has been installed to the instrument. Installation of some USB flash drives may result a long interval between turning the power on and appearance of the Main display. To avoid this, turn the power on after disconnecting the device. The language settings have been changed. Set the appropriate language for the file/folder name (page 16). PSR-SX600 Owner's Manual 107 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
PSR-SX600 Owner’s Manual
107
Troubleshooting
Troubleshooting
Overall
A click or pop is heard when the power is turned on or off.
This is normal. Electrical current is being applied to the instrument.
The power is automatically turned off.
This is normal and due to the Auto Power Off function. If necessary,
set the parameter of the Auto Power Off function (page 15).
Noise is heard from the instrument’s speakers.
Noise may be heard if a mobile phone is used near the instrument
or if the phone is ringing. Turn off the mobile phone, or use it further
away from the instrument.
Noise is heard from the instrument’s speakers or headphones
when using the instrument with the application on smart device.
When you use the instrument along with the application on your
smart device, we recommend that you set “Airplane Mode” to “ON”
on your smart device in order to avoid noise caused by communi-
cation.
In the LCD, there are some specific points that are always lit or
unlit.
These are the result of defective pixels and occasionally occur in
TFT-LCDs; they do not indicate a problem in operation.
There is a slight difference in sound quality among different notes
played on the keyboard.
This is normal and is a result of the instrument’s sampling system.
Some Voices have a looping sound.
Some noise or vibrato is noticeable at higher pitches, depending
upon the Voice.
The overall volume is too low or no sound is heard.
The master volume may be set too low. Set it to an appropriate
level with the [MASTER VOLUME] dial.
All keyboard parts are set to off. Use the PART ON/OFF [RIGHT 1]/
[RIGHT 2]/[LEFT] button to turn it on.
The volume of the individual parts may be set too low. Raise the
volume in the Balance display (page 56).
Make sure the desired channel is set to On (pages 54, 65).
Headphones are connected, disabling the speaker output. Unplug
the headphones.
Make sure that the Speaker setting is set to On:
[MENU]
→
Menu2
→
Utility
→
[ENTER]
→
Config1.
The [FADE IN/OUT] button is on, muting the sound. Press the
[FADE IN/OUT] button to turn the function off.
The sound is distorted or noisy.
The volume may be turned up too high. Make sure all relevant vol-
ume settings are appropriate.
This may be caused by certain effects or filter settings. Check the
effect or filter settings and change them accordingly, referring to
the Reference Manual.
Not all simultaneously played notes sound.
You are probably exceeding the maximum polyphony (page 110)
of the instrument. When the maximum polyphony is exceeded, the
earliest played notes will stop sounding, letting the latest played
notes sound.
The keyboard volume is lower than the Song/Style playback vol-
ume.
The volume of the keyboard parts may be set too low. Raise the
volume in the Balance display (page 56).
The Main display does not appear even when turning the power
on.
This may occur if a USB flash drive has been installed to the instru-
ment. Installation of some USB flash drives may result a long inter-
val between turning the power on and appearance of the Main
display. To avoid this, turn the power on after disconnecting the
device.
Some characters of the file/folder name are garbled.
The language settings have been changed. Set the appropriate
language for the file/folder name (page 16).