Yamaha R-N500 Owners Manual - Page 47

ADDITIONAL INFORMATION, Troubleshooting, General

Get Yamaha R-N500 PDF manuals and user guides View all Yamaha R-N500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

ADDITIONAL INFORMATION Troubleshooting Troubleshooting Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, set this unit to standby mode, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. ■ General Problem Cause Remedy This unit fails to turn on. No sound The sound suddenly goes off. Only the speaker on one side can be heard. The protection circuitry has been activated three times consecutively. If the unit is in this condition, the standby indicator on the unit blinks when you try to turn on the power. As a safety precaution, capability to turn on the power is disabled. Contact your nearest Yamaha dealer or service center to request repair. The power cable is not connected or the plug is not completely inserted. Connect the power cable firmly. The impedance setting is incorrect. Set the impedance to match your speakers. The protection circuitry has been activated Check that the speaker wires are not touching each because of a short circuit, etc. other and then turn the power of this unit back on. This unit has been exposed to a strong external electric shock (such as lightning or strong static electricity). Set this unit to standby mode, disconnect the power cable, plug it back in after 30 seconds, then use it normally. Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables may be defective. No appropriate input source has been selected. Select an appropriate input source with the INPUT selector on the front panel (or one of the input selection keys on the remote control). The SPEAKERS A/B switches are not set Turn on the corresponding SPEAKERS A or properly. SPEAKERS B. Speaker connections are not secure. Secure the connections. Output has been muted. Turn off the mute. The Max volume or Initial volume setting Set the setting to a higher value. is set too low. The component corresponding to the selected input source is turned off or is not playing. Turn the component on and make sure it is playing. The audio output of a device connected to a digital audio input (COAXIAL 1-2/ OPTICAL 1-2 jacks) is set to other than PCM. Set the audio output of the connected device to PCM. The protection circuitry has been activated because of a short circuit, etc. Set the speaker impedance to match your speakers. Check that the speaker wires are not touching each other and then turn the power of this unit back on. This unit has become too hot. Make sure the openings on the top panel are not blocked. The auto power standby function has turned this unit off. Change the auto power standby ("AutoPowerStdby" in the "SETUP" menu) to a longer setting or turn off. Incorrect cable connections. Connect the cables properly. If the problem persists, the cables may be defective. Incorrect setting for the BALANCE control. Set the BALANCE control to the appropriate position. See page - - 11 10 - 10 14 14 10 8 36 - - 11 10 - 37 10 15 ADDITIONAL INFORMATION English 43 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Troubleshooting
43
En
ADDITIONAL
INFORMATION
English
Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or
if the instructions below do not help, set this unit to standby mode, disconnect the power cable, and contact the nearest
authorized Yamaha dealer or service center.
■
General
Troubleshooting
Problem
Cause
Remedy
See
page
This unit fails to turn
on.
The protection circuitry has been activated
three times consecutively. If the unit is in
this condition, the standby indicator on the
unit blinks when you try to turn on the
power.
As a safety precaution, capability to turn on the power
is disabled. Contact your nearest Yamaha dealer or
service center to request repair.
—
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
—
The impedance setting is incorrect.
Set the impedance to match your speakers.
11
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
10
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to standby mode, disconnect the power
cable, plug it back in after 30 seconds, then use it
normally.
—
No sound
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
10
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or one of the input
selection keys on the remote control).
14
The SPEAKERS A/B switches are not set
properly.
Turn on the corresponding SPEAKERS A or
SPEAKERS B.
14
Speaker connections are not secure.
Secure the connections.
10
Output has been muted.
Turn off the mute.
8
The Max volume or Initial volume setting
is set too low.
Set the setting to a higher value.
36
The component corresponding to the
selected input source is turned off or is not
playing.
Turn the component on and make sure it is playing.
—
The audio output of a device connected to
a digital audio input (COAXIAL 1-2/
OPTICAL 1-2 jacks) is set to other than
PCM.
Set the audio output of the connected device to PCM.
—
The sound suddenly
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
Set the speaker impedance to match your speakers.
11
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
10
This unit has become too hot.
Make sure the openings on the top panel are not
blocked.
—
The auto power standby function has
turned this unit off.
Change the auto power standby (“AutoPowerStdby”
in the “SETUP” menu) to a longer setting or turn off.
37
Only the speaker on
one side can be
heard.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
10
Incorrect setting for the BALANCE
control.
Set the BALANCE control to the appropriate
position.
15
ADDITIONAL INFORMATION