Yamaha RX V663 Owner's Manual - Page 122

After Auto Setup, W-1:out Of Phase, W-2:over 24m 80ft, W-3:level Error, W-4:check Prns - subwoofer connection

Get Yamaha RX V663 - AV Receiver PDF manuals and user guides
UPC - 027108930121
View all Yamaha RX V663 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 122 highlights

Troubleshooting After AUTO SETUP Warning message Cause Remedy W-1:OUT OF PHASE W-2:OVER 24m (80ft) W-3:LEVEL ERROR W-4:CHECK PRNS Speaker polarity is not correct. This message Check the speaker connections for proper may appear depending on the speakers even polarity (+ or -). when the speakers are connected correctly. The distance between the speaker and the listening position is over 24 m (80 ft). Bring the speaker closer to the listening position. The difference of volume level among speakers is excessive. Readjust the speaker installation so that all speakers are set in locations with similar conditions. Check the speaker connections. Use speakers of similar quality. When "SWFR: TOO LOUD"or "SWFR: TOO LOW" appears in the result screen, the output volume of the subwoofer. "EXTRA SP ASSIGN" is set to Check the presence speaker connections. "PRESENCE", though the presence channel Set "EXTRA SP ASSIGN" to a setting other signals are not detected. than "PRESENCE". Notes • If the "ERROR" or "WARNING" screens appears, check the cause of the problem, then run "AUTO SETUP" again. • If a warning message "W-1", "W-2" or "W-3" appears, corrections are made, but they may not be optimal. • If an error message "E-10" occurs repeatedly, contact a qualified Yamaha service center. See page 14 - - 14 - 32 14 33 118 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
118
En
Troubleshooting
After AUTO SETUP
•
If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.
•
If a warning message “W-1”, “W-2” or “W-3” appears, corrections are made, but they may not be optimal.
•
If an error message “E-10” occurs repeatedly, contact a qualified Yamaha service center.
Warning message
Cause
Remedy
See
page
W-1:OUT OF PHASE
Speaker polarity is not correct. This message
may appear depending on the speakers even
when the speakers are connected correctly.
Check the speaker connections for proper
polarity (+ or –).
14
W-2:OVER 24m (80ft)
The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker closer to the listening
position.
—
W-3:LEVEL ERROR
The difference of volume level among
speakers is excessive.
Readjust the speaker installation so that all
speakers are set in locations with similar
conditions.
—
Check the speaker connections.
14
Use speakers of similar quality.
—
When “SWFR: TOO LOUD”or “SWFR:
TOO LOW” appears in the result screen, the
output volume of the subwoofer.
32
W-4:CHECK PRNS
“EXTRA SP ASSIGN” is set to
“PRESENCE”, though the presence channel
signals are not detected.
Check the presence speaker connections.
14
Set “EXTRA SP ASSIGN” to a setting other
than “PRESENCE”.
33
Notes