ZyXEL P-1100 User Guide - Page 47

Remote Node Configuration for LAN to LAN

Get ZyXEL P-1100 PDF manuals and user guides View all ZyXEL P-1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Prestige 1100 Internet Access Router Chapter 4: Remote Node Configuration for LAN to LAN A remote node is required for placing calls to a remote gateway. A remote node represents both the gateway and the network behind it across a WAN connection. Note that when you use Menu 4 to set up Internet access, you are actually configuring the remote node. In this chapter, we will discuss the parameters that are protocol independent. The protocol-dependent configuration will be covered in subsequent chapters. This section describes the protocol-independent parameters for a remote node. 4.1 Leased Line Remote Node Profile To configure a remote node, enter 11 to select Menu 11.1 - Remote Node Setup. Menu 11.1 - Remote Node Profile Rem Node Name= ? Active= Yes Route= IP Bridge= No Incoming: Rem Login= ? Rem Password= ******** Outgoing: My Login= ? My Password= ******** Authen= CHAP/PAP Edit PPP Options= No Rem IP Addr= ? Edit IP/IPX/Bridge= No Input Filter Sets: Protocol filters = Device filters = Output Filter Sets= Protocol filters = Device filters = Press ENTER to CONFIRM or ESC to CANCEL: Press Space Bar to Toggle. Figure 4-1 Menu 11.1 - Remote Node Profile for Leased Lines The following table contains the instructions on how to configure the Remote Node Menu for leased lines. Remote Node Configuration 4-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Prestige 1100 Internet Access Router
Remote Node Configuration
4-1
Chapter 4:
Remote Node Configuration for LAN to LAN
A remote node is required for placing calls to a remote gateway.
A remote node represents both the
gateway and the network behind it across a WAN connection.
Note that when you use Menu 4 to set up
Internet access, you are actually configuring the remote node.
In this chapter, we will discuss the parameters that are protocol independent. The protocol-dependent
configuration will be covered in subsequent chapters.
This section describes the protocol-independent parameters for a remote node.
4.1
Leased Line Remote Node Profile
To configure a remote node, enter 11 to select Menu 11.1 - Remote Node Setup.
Figure 4-1 Menu 11.1 - Remote Node Profile for Leased Lines
The following table contains the instructions on how to configure the Remote Node Menu for leased lines.
Menu 11.1 - Remote Node Profile
Rem Node Name= ?
Active= Yes
Incoming:
Rem Login= ?
Rem Password= ********
Outgoing:
My Login= ?
My Password= ********
Authen= CHAP/PAP
Route= IP
Bridge= No
Edit PPP Options= No
Rem IP Addr= ?
Edit IP/IPX/Bridge= No
Input Filter Sets:
Protocol filters =
Device filters =
Output Filter Sets=
Protocol filters =
Device filters =
Press ENTER to CONFIRM or ESC to CANCEL:
Press Space Bar to Toggle.