ZyXEL P-1100 User Guide - Page 52

Remote Node Setup

Get ZyXEL P-1100 PDF manuals and user guides View all ZyXEL P-1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Prestige 1100 Internet Access Router 5.2 Remote Node Setup Follow the procedure in the Remote Node Configuration Chapter to configure the protocol-independent parameters in Menu 11 - Remote Node Profile. For the TCP/IP parameters, follow the instructions below. Follow the steps below to edit Menu 11.3 - Remote Node Network Layer Options shown in Figure 5-2: Step 1. In Menu 11.1, make sure [IP] is among the protocols in the Route field. (The Route field should display Route = IP or Route = IP + IPX.) Step 2. Move the cursor to the [Edit IP/IPX/Bridge] field, then press the space bar to toggle and set the value to [Yes], and press [ENTER] to edit Menu 11.3 - Network Layer Options. Menu 11.3 - Remote Node Network Layer Options IP Options: Rem IP Addr: 0.0.0.0 Rem Subnet Mask= 0.0.0.0 My WAN Addr= 0.0.0.0 Single User Account= No Metric= 2 Private= No RIP Direction= Both Version= RIP-2B Multicast = IGMP-v2 IP Policies= IPX Options: Rem LAN Net #= N/A My WAN Net #= N/A Hop Count= N/A Tick Count= N/A W/D Spoofing(min)= N/A SAP/RIP Timeout(min)= N/A Bridge Options: Ethernet Addr Timeout(min)= N/A Enter here to CONFIRM or ESC to CANCEL: Figure 5-2 Menu 11.3- Remote Node TCP/IP Options 5-2 Remote Node TCP/IP Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Prestige 1100 Internet Access Router
5-2
Remote Node TCP/IP Configuration
5.2
Remote Node Setup
Follow the procedure in the
Remote Node Configuration Chapter
to configure the protocol-independent
parameters in Menu 11 - Remote Node Profile.
For the TCP/IP parameters, follow the instructions below.
Follow the steps below to edit
Menu 11.3 - Remote Node Network Layer Options
shown in Figure 5-2:
Step 1.
In Menu 11.1, make sure [IP] is among the protocols in the Route field. (The Route field should
display Route = IP or Route = IP + IPX.)
Step 2.
Move the cursor to the [Edit IP/IPX/Bridge] field, then press the space bar to toggle and set the
value to
[Yes]
, and press
[ENTER]
to edit
Menu 11.3 - Network Layer Options
.
Figure 5-2 Menu 11.3- Remote Node TCP/IP Options
Menu 11.3 - Remote Node Network Layer Options
IP Options:
Rem IP Addr: 0.0.0.0
Rem Subnet Mask= 0.0.0.0
My WAN Addr= 0.0.0.0
Single User Account= No
Metric= 2
Private= No
RIP Direction= Both
Version= RIP-2B
Multicast = IGMP-v2
IP Policies=
IPX Options:
Rem LAN Net #= N/A
My WAN Net #= N/A
Hop Count= N/A
Tick Count= N/A
W/D Spoofing(min)= N/A
SAP/RIP Timeout(min)= N/A
Bridge Options:
Ethernet Addr Timeout(min)= N/A
Enter here to CONFIRM or ESC to CANCEL: