Brother International BAS-705 Instruction Manual - English - Page 53

Adjusting slider base F, 1-3. Adjusting the height of the slider bracket, u

Get Brother International BAS-705 PDF manuals and user guides View all Brother International BAS-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

6. STANDARD ADJUSTMENT (MECHANISMS) 6-1-2. Adjusting slider base F q w !1 !2 r t e !0 1. Loosen the two bolts q, move slider base F w so that it is aligned with fork bracket F e, and then tighten the bolts q. NOTE: ˔Check that loosen loop presser plate B r and loosen loop presser plate F t do not touch loop presser UB y or loop presser UF u when the air has been released and the fork bracket is moved to about the middle of loop presser F i and loop presser B o. ˔If the upper guide plate !0 gets in the way, remove the two bolts !1 and then remove the upper guide plate !0. ˔Refer to "6-1-5 Adjusting the upper guide plates" on page 50 for details on the upper guide plate. 2. Loosen the two bolts !1, move the loop hold plate !2 in between loop presser F i and loop presser B o, and then tighten the bolt !1. !1 y o i u !2 6-1-3. Adjusting the height of the slider bracket 1. Release the air, loosen the bolt q, and then move the cylinder stopper w up by the amount of drop. After adjusting, tighten the bolt q. NOTE: Raise the slider bracket as high as possible while ensuring that the belt loops do not go under the loop pressers B e F r. w q e r ʕ50 ʕ B A S -705

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
6. STANDARD ADJUSTMENT (MECHANISMS)
6-1-2. Adjusting slider base F
1.
Loosen the two bolts
q
, move slider base F
w
so
that it is aligned with fork bracket F
e
, and then
tighten the bolts
q
.
NOTE:
●
Check that loosen loop presser plate B
r
and
loosen loop presser plate F
t
do not touch
loop presser UB
y
or loop presser UF
u
when
the air has been released and the fork bracket
is moved to about the middle of loop presser
F
i
and loop presser B
o
.
●
If the upper guide plate
!
0
gets in the way,
remove the two bolts
!
1
and then remove the
upper guide plate
!
0
.
●
Refer to "6-1-5 Adjusting the upper guide
plates" on page 50 for details on the upper
guide plate.
2.
Loosen the two bolts
!1
, move the loop hold plate
!
2
in between loop presser F
i
and loop presser B
o
, and then tighten the bolt
!
1
.
1.
Release the air, loosen the bolt
q
, and then move
the cylinder stopper
w
up by the amount of drop.
After adjusting, tighten the bolt
q
.
NOTE:
Raise the slider bracket as high as possible
while ensuring that the belt loops do not go
under the loop pressers B
e
F
r
.
6-1-3. Adjusting the height of the slider bracket
―
50
―
BAS-705
e
r
q
w
q
w
!
2
r
e
t
!
1
y
u
!
0
!
1
i
o
!
2