Brother International BAS-705 Instruction Manual - English - Page 88

Loop setting sensor, and then find the position

Get Brother International BAS-705 PDF manuals and user guides View all Brother International BAS-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

11-4. Loop setting sensor ...... (S41959-001) w q 11. OPTIONS e r Installation 1. Install the loop setting sensor assembly q to slider base F w with the two bolts. 2. Insert the 3-pin connector e coming out from the control box to the loop setting sensor r. Adjustment NOTE: Carry out this adjustment while loop presser foot F is raised. LED r 1. Loosen the bolts of loop sensor plate 1 t, loop sen sor plate 2 y and the sensor r. 2. Move the sensor r up and down so that the sensor t light beam is aligned with the reflective surface i of loop presser foot F u, and then find the position where the LED of the sensor r illuminates steadily. NOTE: The appropriate distance between the reflective sur y face i of loop presser foot F u and the sensor r is 40 - 45 mm. 3. After adjusting, tighten the bolts. 4. Carry out actions such as setting and removing the belt loops and moving loop presser foot F u, and check that the LED illuminates steadily. 40ʙ50 mm u i ʕ 85 ʕ B A S -705

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
11. OPTIONS
11-4. Loop setting sensor
......
(S41959-001)
<
Installation
>
1. Install the loop setting sensor assembly
q
to slider base F
w
with the two bolts.
2. Insert the 3-pin connector
e
coming out from the control box to the loop setting sensor
r
.
<
Adjustment
>
NOTE: Carry out this adjustment while loop presser foot F is raised.
―
85
―
BAS-705
w
q
e
r
1. Loosen the bolts of loop sensor plate 1
t
, loop sen
sor plate 2
y
and the sensor
r
.
2. Move the sensor
r
up and down so that the sensor
light beam is aligned with the reflective surface
i
of
loop presser foot F
u
, and then find the position
where the LED of the sensor
r
illuminates steadily.
NOTE:
The appropriate distance between the reflective sur
face
i
of loop presser foot F
u
and the sensor
r
is 40 - 45 mm.
3. After adjusting, tighten the bolts.
4. Carry out actions such as setting and removing the
belt loops and moving loop presser foot F
u
, and check
that the LED illuminates steadily.
r
LED
t
y
i
�
40
～
50
mm
u