Brother International BAS-705 Instruction Manual - English - Page 82

Mechanisms

Get Brother International BAS-705 PDF manuals and user guides View all Brother International BAS-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

10-2. Mechanisms Problem Cause Check 10. TROUBLESHOOTING Remedy Page Belt loops are curved over front of loop presser F. Belt loops are lifted up when coming out from cutter. Belt loops are fed underneath loop presser B. Belt loops are fed underneath loop presser F. Loop presser F is too low. Belt loops are lifted up when fed out. Relative heights of loop presser B and loop presser F Upper guide plates are not installed. Belt loops are too curled. Belt loop curl Loop support T is too high. Belt loops are too curled. Distance between loop support T and the belt loops Belt loop curl Loop support T is too low. Loop presser B is too high. Belt loops are too curled. Distance between loop support T and the belt loops Distance between cutter outlet and loop presser B Belt loop curl Loop presser F is too high. Widths of loop pressers F and B are too narrow. Relative heights of loop presser B and loop presser F Width of loop pressers being used Belt loops are too curled. Belt loop curl Adjust the height of the loop presser F slider 50 bracket. Install the upper guide plates. 51 Replace with belt loops which are not so curled. Adjust loop support T. 55 Replace with belt loops which are not so curled. Adjust loop support T. Adjust the height of the loop presser B slider bracket. Replace with belt loops which are not so curled. 55 50 Adjust the height of the loop presser F slider 50 bracket. Replace the lop pressers with wider ones. 51 Replace with belt loops which are not so curled. ʕ 79 ʕ B A S -705

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
10. TROUBLESHOOTING
10-2. Mechanisms
―
79
―
BAS-705
Distance between cutter
outlet and loop presser
B
Belt loop curl
Relative heights of loop
presser B and loop
presser F
Width of loop pressers
being used
Belt loop curl
Distance between loop
support T and the belt
loops
Belt loop curl
Distance between loop
support T and the belt
loops
Belt loop curl
Upper guide plates are
not installed.
Relative heights of loop
presser B and loop
presser F
Loop presser F is too
low.
Belt loops are lifted up
when fed out.
Belt loops are too curled.
Loop support T is too
high.
Belt loops are too curled.
Loop support T is too
low.
Loop presser B is too
high.
Belt loops are too curled.
Loop presser F is too
high.
Widths of loop pressers
F and B are too narrow.
Belt loops are too curled.
Belt loops are fed
underneath loop presser
F.
Belt loops are fed
underneath loop presser
B.
Adjust loop support T.
55
Adjust the height of the
loop presser B slider
bracket.
50
Replace with belt loops
which are not so curled.
�
Adjust the height of the
loop presser F slider
bracket.
50
Replace the lop pressers
with wider ones.
51
Replace with belt loops
which are not so curled.
�
Replace with belt loops
which are not so curled.
�
Adjust loop support T.
55
Replace with belt loops
which are not so curled.
�
Install the upper guide
plates.
51
Adjust the height of the
loop presser F slider
bracket.
50
Belt loops are lifted up
when coming out from
cutter.
Problem
Cause
Check
Remedy
Page
Belt loops are curved
over front of loop
presser F.