Brother International BAS-705 Instruction Manual - English - Page 75

Overheating of X-Y feed circuit, position for X-Y feed. - area code

Get Brother International BAS-705 PDF manuals and user guides View all Brother International BAS-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

9. ERROR CODES Error code E-160 E-170 Problem Solution Loop length data, bobbin thread counter data, production counter data or sewing speed data is corrupted. Lower shaft module was open when sewing started. q Turn off power switch. w Initialize the sewing data. q Close the lower shaft. w Press the RESET switch. E-171 q Check the lock cylinder and sensor. Lower shaft module locking error w Press the RESET switch. E-181 182 E-190 E-1A0 E-1A1 E-202 Upper thread breaks at the first Refer to pages 29. and second bar tacking. q Remove the belt loop which was set incorrectly. Loop setting error w Press the RESET switch. e Press the LOOP switch and then set a new belt loop. Communication error between Press the RESET switch. main circuit board and X-Y feed circuit board. Communication error between Press the RESET switch. main circuit board and panel circuit board. Motor does not operate, or problem q Turn the machine pulley to check that it is not locked. with synchronizer signal. w Press the RESET switch. E-203 E-204 E-20A The pattern was found to be Press the RESET switch and then reset the scale. outside the sewing area during a scale check. The pattern was found to be over Press the RESET switch and then reset the scale. the maximum pitch during a scale check. Error detecting X or Y home Check the operation at the X or Y home position. position for X-Y feed. E-20D Overheating of X-Y feed circuit Turn off the power and check the operation of the board fan inside the box. E-20E  Reading or writing error of EEPROM on in X-Y feed circuit board q Turn off power switch. w Wait 10 seconds or more, and then turn the power back on again. ʕ 72 ʕ B A S -705

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
9. ERROR CODES
―
72
―
BAS-705
E-160
E-170
E-171
E-181
�
182
E-190
E-1A0
E-1A1
E-202
E-203
E-204
E-20A
E-20D
E-20E
�
Loop length data, bobbin thread counter
data, production counter data or sewing
speed data is
corrupted.
Lower shaft module was open
when sewing started.
Lower shaft module locking error
Upper thread breaks at the first
and second bar tacking.
Loop setting error
Communication error between
main circuit board and X-Y feed
circuit board.
Communication error between
main circuit board and panel
circuit board.
Motor does not operate, or problem
with synchronizer signal.
The pattern was found to be
outside the sewing area during a
scale check.
The pattern was found to be over
the maximum pitch during a scale
check.
Error detecting X or Y home
position for X-Y feed.
Overheating of X-Y feed circuit
board
Reading or writing error of
EEPROM on in X-Y feed circuit
board
q
Turn off power switch.
w
Initialize the sewing data.
q
Close the lower shaft.
w
Press the RESET switch.
q
Check the lock cylinder and sensor.
w
Press the RESET switch.
Refer to pages 29.
q
Remove the belt loop which was set incorrectly.
w
Press the RESET switch.
e
Press the LOOP switch and then set a new belt loop.
Press the RESET switch.
Press the RESET switch.
q
Turn the machine pulley to check that it is not locked.
w
Press the RESET switch.
Press the RESET switch and then reset the scale.
Press the RESET switch and then reset the scale.
Check the operation at the X or Y home position.
Turn off the power and check the operation of the
fan inside the box.
q
Turn off power switch.
w
Wait 10 seconds or more, and then turn the
power back on again.
Error code
Problem
Solution