Brother International MFC-J270w Network Users Manual - English - Page 59

LCD shows, Connection status, Action, Connected, Connection Error, No Access Point

Get Brother International MFC-J270w PDF manuals and user guides View all Brother International MFC-J270w manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Wireless configuration using the Brother installer application i If the LCD shows Connected, the machine has successfully connected to your router or access point. You can now use your machine in a wireless network. If the LCD shows Connection Error, a session overlap has been detected. The machine has detected more than one access point/router on your network with the Wi-Fi Protected Setup mode or AOSS™ mode enabled. Make sure that only one access point/router has the Wi-Fi Protected Setup mode or the AOSS™ mode enabled and try starting from f again. If the LCD shows No Access Point, the machine has not detected your access point/router on your network with the Wi-Fi Protected Setup mode or AOSS™ mode enabled. Move the machine closer to your access point/router and try starting from f again. If the LCD shows Connection Fail, the machine has not successfully connected to your access 4 point/router. Try starting from f again. If the same message is indicated again, reset the machine back to the default factory settings and try again. (For resetting, see Restoring the network settings to factory default on page 77.) LCD messages when using the WPS/AOSS™ control panel menu LCD shows Setting WLAN Connecting WPS Connecting AOSS Connected Connection Error No Access Point Connection Fail Connection status Searching or accessing the access point, and downloading settings from the access point. Action - Connecting to the access point. - Connection succeeded. Session overlap has been detected. The access point detection failed. The machine was not able to connect with the access point. - Check that only one router or access point has the Wi-Fi Protected Setup mode or AOSS™ mode enabled and try starting from step f again. Move the machine closer to your access point/router and try starting from step f again.  Try starting from step f again.  If the same message reappears, reset the machine back to the factory settings and try again. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Wireless configuration using the Brother installer application
52
4
i
If the LCD shows
Connected
, the machine has successfully connected to your router or access point.
You can now use your machine in a wireless network.
If the LCD shows
Connection Error
, a session overlap has been detected. The machine has
detected more than one access point/router on your network with the Wi-Fi Protected Setup mode or
AOSS™ mode enabled. Make sure that only one access point/router has the Wi-Fi Protected Setup
mode or the AOSS™ mode enabled and try starting from
f
again.
If the LCD shows
No Access Point
, the machine has not detected your access point/router on your
network with the Wi-Fi Protected Setup mode or AOSS™ mode enabled. Move the machine closer to
your access point/router and try starting from
f
again.
If the LCD shows
Connection Fail
, the machine has not successfully connected to your access
point/router. Try starting from
f
again. If the same message is indicated again, reset the machine back
to the default factory settings and try again. (For resetting, see
Restoring the network settings to factory
default
on page 77.)
LCD messages when using the WPS/AOSS™ control panel menu
LCD shows
Connection status
Action
Setting WLAN
Searching or accessing the access point,
and downloading settings from the access
point.
—
Connecting WPS
Connecting AOSS
Connecting to the access point.
—
Connected
Connection succeeded.
—
Connection Error
Session overlap has been detected.
Check that only one router or access
point has the Wi-Fi Protected Setup
mode or AOSS™ mode enabled and try
starting from step
f
again.
No Access Point
The access point detection failed.
Move the machine closer to your
access point/router and try starting from
step
f
again.
Connection Fail
The machine was not able to connect with
the access point.
Try starting from step
f
again.
If the same message reappears,
reset the machine back to the
factory settings and try again.