Cisco 7206VXR Installation Guide - Page 73

Attaching the Chassis Rack-Mount and Cable-Management Brackets,

Page 73 highlights

Chapter 3 Installing the Cisco 7206 Rack-Mounting the Cisco 7206 Figure 3-5 Rack-Mounting the Chassis in a Four-Post Rack with Installed Cable-Management Brackets-Front Installation Shown Rack-mount bracket EN TD TC RD RC LB CD TD TC RD RC LB CD TD TC RD RC LB CD TD TC RD RC LB CD ENABLED 0 5 3 1 Cisco 7200 Series ENABLED PCMCIA 1 2 3 0 1 LINK 2 3 ETHERNET 10BT FAST SERIAL ENABLED 0 MII 1 LINK RJ45 2 RX 3 TX TOKEN RING 6 FAST ETHERNET 4 ETHERNET-10BFL 2 RX 0 TX RX TX TX RX EN RX 0 TX 4 3 2 1 SLOT 1 FE MII RJ-45 RESET CPU FAST ETHERNET INPUT/OUTPUT CONTROLLER 0 EJECT SLOT 0 II MEN RJE4N5 RJL4IN5 K R 1O PWK O Cable-management bracket H9452 If you are rack-mounting a Cisco 7206 router from the rear, the rack-mount brackets are installed at the rear of the chassis, and the cable-management brackets are installed at the front of the chassis. You must install both sets of brackets before you install the chassis in the rack. Attaching the Chassis Rack-Mount and Cable-Management Brackets This section explains how to install the rack-mount and cable-management brackets at the front and the rear of the Cisco 7206. Before installing the chassis in the rack, you must install a rack-mount bracket on each side of the front or rear of the chassis. If you are rack-mounting the chassis from the front and you plan to use the cable-management brackets, you must install the cable-management brackets when you install the rack-mount brackets on the chassis. If you are rack-mounting the chassis from the rear, you may install the rack-mount and cable-management brackets separately; however, both sets of brackets must be installed on the chassis before the chassis is installed in the rack. The parts and tools required for installing the rack-mount and cable-management brackets are listed in Chapter 2, "Preparing for Installation," the "Tools for Installation" section on page 2-8. OL-5102-02 Cisco 7206 Installation and Configuration Guide 3-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150

3-5
Cisco 7206 Installation and Configuration Guide
OL-5102-02
Chapter 3
Installing the Cisco 7206
Rack-Mounting the Cisco 7206
Figure 3-5
Rack-Mounting the Chassis in a Four-Post Rack with Installed Cable-Management
Brackets—Front Installation Shown
If you are rack-mounting a Cisco 7206 router from the rear, the rack-mount brackets are installed at the
rear of the chassis, and the cable-management brackets are installed at the front of the chassis. You must
install both sets of brackets
before
you install the chassis in the rack.
Attaching the Chassis Rack-Mount and Cable-Management Brackets
This section explains how to install the rack-mount and cable-management brackets at the front and the
rear of the Cisco 7206. Before installing the chassis in the rack, you must install a rack-mount bracket
on each side of the front or rear of the chassis. If you are rack-mounting the chassis from the front and
you plan to use the cable-management brackets, you must install the cable-management brackets when
you install the rack-mount brackets on the chassis.
If you are rack-mounting the chassis from the rear, you may install the rack-mount and
cable-management brackets separately; however, both sets of brackets must be installed on the chassis
before the chassis is installed in the rack.
The parts and tools required for installing the rack-mount and cable-management brackets are listed in
Chapter 2, “Preparing for Installation,”
the
“Tools for Installation” section on page 2-8
.
4
6
FAST SERIAL
EN
TD
TC
RD
RC
LB
CD
TD
TC
RD
RC
LB
CD
TD
TC
RD
RC
LB
CD
TD
TC
RD
RC
LB
CD
ETHERNET-10BFL
EN
RX
0
1
2
3
4
TX
RX
TX
RX
TX
RX
TX
RX
TX
TOKEN RING
0
1
2
3
ETHERNET 10BT
ENABLED
0
2
1
3
LINK
0
1
2
3
ENABLED
MII
LINK
RJ45
FAST ETHERNET
0
3
5
1
2
0
Cisco 7200
Series
H9452
FAST ETHERNET INPUT/OUTPUT CONTROLLER
ENABLED
PCMCIA
EJECT
SLOT 0
SLOT 1
FE MII
Rack-mount
bracket
Cable-management bracket