Cisco 7206VXR Installation Guide - Page 90

Warning, Step 1, Stripping the DC-Input Leads

Get Cisco 7206VXR - VPN Bundle Router PDF manuals and user guides
UPC - 746320975061
View all Cisco 7206VXR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Connecting Power Chapter 3 Installing the Cisco 7206 Warning Before completing any of the following steps, and to prevent short-circuit or shock hazards, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position. Warning When you install the unit, the ground connection must always be made first and disconnected last. Step 1 Step 2 Ensure that no current is flowing through the DC power supply leads. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position. Using a wire stripper, strip approximately 0.55 inch (14 mm) from the -V, +V, and ground leads (refer to Figure 3-22). Figure 3-22 Stripping the DC-Input Leads 0.55 in. (14 mm) H8624 Step 3 Step 4 At the rear of the router, check that the power switch on the power supply is in the off (O) position (refer to Figure 3-23). Insert the stripped end of the ground lead all the way into the ground lead receptacle on the DC-input power supply and tighten the receptacle screw using a 3/16-inch flat-blade screwdriver (refer to Figure 3-23). 3-22 Cisco 7206 Installation and Configuration Guide OL-5102-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
3-22
Cisco 7206 Installation and Configuration Guide
OL-5102-02
Chapter 3
Installing the Cisco 7206
Connecting Power
Warning
Before completing any of the following steps, and to prevent short-circuit or shock hazards, ensure
that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker
on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and
tape the switch handle of the circuit breaker in the OFF position.
Warning
When you install the unit, the ground connection must always be made first and disconnected last.
Step 1
Ensure that no current is flowing through the DC power supply leads. To ensure that all power is OFF,
locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to
the OFF position, and tape the switch handle of the circuit breaker in the OFF position.
Step 2
Using a wire stripper, strip approximately 0.55 inch (14 mm) from the –V, +V, and ground leads (refer
to
Figure 3-22
).
Figure 3-22
Stripping the DC-Input Leads
Step 3
At the rear of the router, check that the power switch on the power supply is in the off (O) position (refer
to
Figure 3-23
).
Step 4
Insert the stripped end of the ground lead all the way into the ground lead receptacle on the DC-input
power supply and tighten the receptacle screw using a 3/16-inch flat-blade screwdriver (refer to
Figure 3-23
).
0.55 in.
(14 mm)
H8624