Cisco CISCO876-SEC-I-K9 Configuration Guide - Page 39

Con the Fast Ethernet WAN Interfaces

Page 39 highlights

Chapter 3 Configuring PPP over Ethernet with NAT Configure the Fast Ethernet WAN Interfaces Step 3 Command or Action request-dialin Example: Router(config-vpdn)# request-dialin Router(config-vpdn-req-in)# Purpose Creates a request-dialin VPDN subgroup, indicating the dialing direction, and initiates the tunnel. Step 4 protocol {l2tp | pppoe} Example: Router(config-vpdn-req-in)# protocol pppoe Router(config-vpdn-req-in)# Specifies the type of sessions the VPDN subgroup can establish. Step 5 exit Exits request-dialin VPDN group configuration. Example: Router(config-vpdn-req-in)# exit Router(config-vpdn)# Step 6 exit Example: Router(config-vpdn)# exit Router(config)# Exits VPDN configuration, returning to global configuration mode. Configure the Fast Ethernet WAN Interfaces In this scenario, the PPPoE client (your Cisco router) communicates over a 10/100 Mbps-Ethernet interface on both the inside and the outside. Perform these steps to configure the Fast Ethernet WAN interfaces, starting in global configuration mode: Step 1 Command interface type number Example: Router(config)# interface fastethernet 4 Router(config-if)# Step 2 pppoe-client dial-pool-number number Example: Router(config-if)# pppoe-client dial-pool-number 1 Router(config-if)# Purpose Enters interface configuration mode for a Fast Ethernet WAN interface. Configures the PPPoE client and specifies the dialer interface to use for cloning. OL-5332-01 Cisco 850 Series and Cisco 870 Series Access Routers Software Configuration Guide 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196

3-3
Cisco 850 Series and Cisco 870 Series Access Routers Software Configuration Guide
OL-5332-01
Chapter 3
Configuring PPP over Ethernet with NAT
Configure the Fast Ethernet WAN Interfaces
Configure the Fast Ethernet WAN Interfaces
In this scenario, the PPPoE client (your Cisco router) communicates over a 10/100 Mbps-Ethernet
interface on both the inside and the outside.
Perform these steps to configure the Fast Ethernet WAN interfaces, starting in global configuration
mode:
Step 3
request-dialin
Example:
Router(config-vpdn)#
request-dialin
Router(config-vpdn-req-in)#
Creates a request-dialin VPDN subgroup,
indicating the dialing direction, and initiates the
tunnel.
Step 4
protocol
{
l2tp
|
pppoe
}
Example:
Router(config-vpdn-req-in)#
protocol pppoe
Router(config-vpdn-req-in)#
Specifies the type of sessions the VPDN subgroup
can establish.
Step 5
exit
Example:
Router(config-vpdn-req-in)#
exit
Router(config-vpdn)#
Exits request-dialin VPDN group configuration.
Step 6
exit
Example:
Router(config-vpdn)#
exit
Router(config)#
Exits VPDN configuration, returning to global
configuration mode.
Command or Action
Purpose
Command
Purpose
Step 1
interface
type number
Example:
Router(config)#
interface fastethernet 4
Router(config-if)#
Enters interface configuration mode for a
Fast Ethernet WAN interface.
Step 2
pppoe-client dial-pool-number
number
Example:
Router(config-if)#
pppoe-client
dial-pool-number 1
Router(config-if)#
Configures the PPPoE client and specifies the
dialer interface to use for cloning.