Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 33

Powering Up the Server, Table 2-1, Rear Panel Connections

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

2-7 Table 2-1 Rear Panel Connections Ref. Connector 1 Parallel Connector 2 Serial Connector 3 Serial Connector 4 External SCSI Connector (B) 5 Power Connector Ref. Connector 6 PCI/ISA Expansion Slots 7 Mouse Connector 8 Keyboard Connector 9 RJ-45 Ethernet Connector with 3 NIC LEDs: Active, Link, and 10/100 Speed 10 Video Connector Powering Up the Server After the cables have been connected to the server, you are ready to power up the ProLiant 800 server as shown in Figure 2-2. WARNING: Be sure that the power outlet you plug your power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the power outlet. NOTE: Do not place anything on power cords or cables. Arrange them so that no one may accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp the cord by the plug. 1. Slide the power switch cover plate – to the right. 2. Press the power switch —. Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100 MHz System Bus Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
2-7
Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100 MHz System Bus Setup and Installation
Guide
Table 2-1
Rear Panel Connections
Ref.
Connector
Ref.
Connector
1
Parallel Connector
6
PCI/ISA Expansion Slots
2
Serial Connector
7
Mouse Connector
3
Serial Connector
8
Keyboard Connector
4
External SCSI Connector
(B)
9
RJ-45 Ethernet Connector with
3 NIC LEDs: Active, Link, and
10/100 Speed
5
Power Connector
10
Video Connector
Powering Up the Server
After the cables have been connected to the server, you are ready to power up
the ProLiant 800
server as shown in Figure 2-2.
WARNING
:
Be sure that the power outlet you plug
your power cord into is easily accessible and located
as close to the equipment operator as possible.
When
you need to disconnect power to the equipment, be
sure to unplug the power cord from the power outlet.
NOTE
:
Do not place anything on power cords or cables.
Arrange them so that no one may accidentally step on or trip over
them. Do not pull on a cord or cable. When unplugging from the
electrical outlet, grasp the cord by the plug.
1.
Slide the power switch cover plate
to the right.
2.
Press the power switch
.