Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 42

Removing the Small Access, Panel, the cooling system and removing it while the system is

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

3-5 Removing the Small Access Panel CAUTION: Do not operate the server with the small access panel removed. This panel is an integral part of the cooling system and removing it while the system is running may adversely affect data integrity. To remove the small access panel: 1. If the computer is on, turn it off and disconnect the power cord. 2. Disconnect any other external equipment connected to the computer. 3. If required, open the front bezel. 4. Loosen the top thumbscrew. 5. Slide the small access panel toward the rear of the unit about 0.5 inch (1.5 cm), and then slide the panel to the side of the server. See Figure 3-2. 6. Lift and remove the panel. Figure 3-2. Sliding the small access panel Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
3-5
Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation
Guide
Removing the Small Access
Panel
CAUTION:
Do not operate the server with the small
access panel removed. This panel is an integral part of
the cooling system and removing it while the system is
running may adversely affect data integrity.
To remove the small access panel:
1.
If the computer is on, turn it off and disconnect the power cord.
2.
Disconnect any other external equipment connected to the computer.
3.
If required, open the front bezel.
4.
Loosen the top thumbscrew.
5.
Slide the small access panel toward the rear of the unit about 0.5 inch
(1.5 cm), and then slide the panel to the side of the server. See Figure 3-2.
6.
Lift and remove the panel.
Figure 3-2.
Sliding the small access panel