Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 71

Connecting the Integrated, Wide-Ultra SCSI-3 Controller, to SCSI Devices, Table 4-1

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

4-5 Connecting the Integrated Wide-Ultra SCSI-3 Controller to SCSI Devices Refer to the following table for an overview of cabling SCSI devices internally to the Integrated Wide-Ultra SCSI-3 Controller. Table 4-1 assumes that the controller end of the Wide SCSI cable has not been connected to the Integrated Wide-Ultra SCSI-3 Controller. Table 4-1 Cabling the Integrated SCSI Controller to Internal SCSI Devices NHP* Hard Drives ** Selected Fast-SCSI-2 Tape Drives and SCSI CD-ROM Installed in Removable Media Area 1. Locate the Wide SCSI cable. No additional cables are required. 1. Locate the Wide SCSI cable. No additional cables are required. 2. Connect controller end of Wide SCSI cable to 2. Connect controller end of Wide SCSI cable to Integrated SCSI Controller. Integrated SCSI Controller. 3. Connect wide to standard cable adapter, if needed. 3. Connect wide to standard cable adapter to device. 4 Connect an available connector on SCSI cable 4 Connect an available connector on SCSI cable to the device(s). to the device(s) in the removable media area. 5. Ensure SCSI ID uniquely set on each device. 6. Run System Configuration Utility. 5. Ensure SCSI ID uniquely set on each device. 6. Run System Configuration Utility. * NHP = Non-hot-pluggable ** Selected drives: 2/4 and 4/8 DAT drive, 4/16 TurboDAT drive autoloader Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
4-5
Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation
Guide
Connecting the Integrated
Wide-Ultra SCSI-3 Controller
to SCSI Devices
Refer to the following table for an overview of cabling SCSI devices
internally to the Integrated Wide-Ultra SCSI-3 Controller. Table 4-1 assumes
that the controller end of the Wide SCSI cable has not been connected to the
Integrated Wide-Ultra SCSI-3 Controller.
Table 4-1
Cabling the Integrated SCSI Controller to Internal SCSI Devices
NHP* Hard Drives
** Selected Fast-SCSI-2
Tape Drives and SCSI CD-ROM Installed in
Removable Media Area
1. Locate the Wide SCSI cable. No additional
cables are required.
2. Connect controller end of Wide SCSI cable to
Integrated SCSI Controller.
3. Connect wide to standard cable adapter, if
needed.
4
Connect an available
connector on SCSI cable
to the device(s).
5. Ensure SCSI ID uniquely
set on each device.
6. Run System Configuration Utility.
1. Locate the Wide SCSI cable. No additional
cables are required.
2. Connect controller end of Wide SCSI cable to
Integrated SCSI Controller.
3. Connect wide to standard cable adapter to
device.
4
Connect an available
connector on SCSI cable
to the device(s) in the removable media area.
5. Ensure SCSI ID uniquely set on each device.
6. Run System Configuration Utility.
*
NHP = Non-hot-pluggable
**
Selected drives: 2/4 and 4/8 DAT drive, 4/16 TurboDAT drive autoloader