Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 75

SCSI Cabling of a SMART-2, Array Controller Board, Table 4-3

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

4-9 SCSI Cabling of a SMART-2 Array Controller Board Refer to the following table and figure for an overview of cabling the SMART-2 Controller to internal SCSI devices. Table 4-3 assumes that the controller end of the Wide SCSI cable has not been connected to the Integrated Wide-Ultra SCSI-3 Controller. Table 4-3 Cabling of SMART-2 Controller to Internal SCSI Devices NHP* Hard Drives Selected SCSI Tape Drives and SCSI CD-ROM Installed in Removable Media Area 1. Locate the Wide SCSI cable. No additional cables are required. Not Supported. 2. Connect controller end of Wide SCSI cable to SMART-2 Controller. 3. Connect wide to standard cable adapter to device end of SCSI cable, if needed. 4. Connect an available connector on Wide SCSI cable to the device(s). 5. Ensure SCSI ID uniquely set on each device. 6. Run System Configuration Utility. * NHP = Non-hot-pluggable Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
4-9
Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation
Guide
SCSI Cabling of a SMART-2
Array Controller Board
Refer to the following table and figure for an overview of cabling the
SMART-2 Controller to internal SCSI devices. Table 4-3 assumes that the
controller end of the Wide SCSI cable has not been connected to the
Integrated Wide-Ultra SCSI-3 Controller.
Table 4-3
Cabling of SMART-2 Controller to Internal SCSI Devices
NHP* Hard Drives
Selected SCSI Tape Drives
and SCSI CD-ROM
Installed in Removable Media Area
1. Locate the Wide SCSI cable. No additional
cables are required.
2. Connect controller end of Wide SCSI cable to
SMART-2 Controller.
3. Connect wide to standard cable adapter to
device end of SCSI cable, if needed.
4. Connect an available
connector on Wide SCSI
cable to the device(s).
5. Ensure SCSI ID uniquely set on each device.
6. Run System Configuration Utility.
Not Supported.
*
NHP = Non-hot-pluggable