Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 73

Internal SCSI Cabling of the, Bit Fast-Wide SCSI-2, Controller/P and the Wide, Ultra Controller/P

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

4-7 Internal SCSI Cabling of the 32-Bit Fast-Wide SCSI-2 Controller/P and the WideUltra Controller/P Refer to the following table and figure for an overview of cabling the 32-Bit Fast-Wide SCSI-2 Controller/P and the Wide-Ultra SCSI Controller/P to the internal SCSI devices. Table 4-2 assumes that the controller end of the Wide SCSI cable has not been connected to the Integrated Wide-Ultra SCSI-3 Controller. Table 4-2 Cabling of 32-Bit Fast-Wide SCSI-2 Controller/P and Wide-Ultra Controller/P to Internal SCSI Devices NHP* Hard Drives ** Selected SCSI Tape Drives and SCSI CDROM Drive Installed in Removable Media Area 1. Locate the Wide SCSI cable. No additional cables are required. 1. Locate the Wide SCSI cable. No additional cables are required. 2. Connect controller end of Wide SCSI cable to 2. Connect controller end of Wide SCSI cable to 32-Bit Fast-Wide SCSI-2 Controller/P or Wide- 32-Bit Fast-Wide SCSI-2 Controller/P or Wide- Ultra Controller/P board. Ultra Controller/P board. 3. Connect wide to standard cable adapter to device end of SCSI cable, if needed. 3. Connect wide to standard cable adapter to device end of SCSI cable, if needed. 4 Connect an available connector on SCSI cable 4 Connect an available connector on Wide SCSI to device(s). cable to device(s) in the removable media area. 5. Ensure SCSI ID uniquely set on each device. 5. Ensure SCSI ID uniquely set on each device. 6. Run System Configuration Utility. 6. Run System Configuration Utility. * NHP = Non-hot-pluggable ** Selected drives: 2/4 and 4/8 DAT drive, 4/16 TurboDAT drive autoloader Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
4-7
Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation
Guide
Internal SCSI Cabling of the
32-Bit Fast-Wide SCSI-2
Controller/P and the Wide-
Ultra Controller/P
Refer to the following table and figure for an overview of cabling the 32-Bit
Fast-Wide SCSI-2 Controller/P and the Wide-Ultra SCSI Controller/P to the
internal SCSI devices. Table 4-2 assumes that the controller end of the Wide
SCSI cable has not been connected to the Integrated Wide-Ultra SCSI-3
Controller.
Table 4-2
Cabling of 32-Bit Fast-Wide SCSI-2 Controller/P and
Wide-Ultra Controller/P to Internal SCSI Devices
NHP* Hard Drives
** Selected SCSI Tape Drives and SCSI CD-
ROM Drive Installed in Removable Media Area
1. Locate the Wide SCSI cable. No additional
cables are required.
2. Connect controller end of Wide SCSI cable to
32-Bit Fast-Wide SCSI-2 Controller/P or Wide-
Ultra Controller/P board.
3. Connect wide to standard cable adapter to
device end of SCSI cable, if needed.
4
Connect an available
connector on SCSI cable
to device(s).
5. Ensure SCSI ID uniquely set on each device.
6. Run System Configuration Utility.
1. Locate the Wide SCSI cable. No additional
cables are required.
2. Connect controller end of Wide SCSI cable to
32-Bit Fast-Wide SCSI-2 Controller/P or Wide-
Ultra Controller/P board.
3. Connect wide to standard cable adapter to
device end of SCSI cable, if needed.
4
Connect an available
connector on Wide SCSI
cable to device(s) in the removable media area.
5. Ensure SCSI ID uniquely set on each device.
6. Run System Configuration Utility.
*
NHP = Non-hot-pluggable
**
Selected drives: 2/4 and 4/8 DAT drive, 4/16 TurboDAT drive autoloader