Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 48

Hardware Installation, and Configuration Poster, included in the shipping box or to

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

4. Remove the processor cage. 3-11 Figure 3-8. Removing the processor cage 5. Turn the cage over, loosen the thumbscrew, and lift the cover to locate the processor and memory components. 6. For installation of these components, refer to the Hardware Installation and Configuration Poster included in the shipping box or to the Processor Cage Configuration Label located on the inside of the large access panel. 7. To reassemble the server, reverse steps 1 through 5. NOTE: If you inadvertently removed the processor cage without turning OFF the power switch, the server automatically powers down. This is not, however, a recommended procedure for powering off the server. Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
3-11
Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation
Guide
4.
Remove the processor cage.
Figure 3-8.
Removing the processor cage
5.
Turn the cage over, loosen the thumbscrew, and lift the cover to locate
the processor and memory components.
6.
For installation of these components, refer to the
Hardware Installation
and Configuration Poster
included in the shipping box or to the
Processor Cage Configuration Label located on the inside of the large
access panel.
7.
To reassemble the server, reverse steps 1 through 5.
NOTE
:
If you inadvertently removed the processor cage
without turning OFF the power switch, the server automatically
powers down. This is not, however, a recommended procedure
for powering off the server.