Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 60

Installing External Storage, Devices, Instructions for Mass Storage SCSI Devices

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

3-23 Installing External Storage Devices Optional mass storage devices can be connected to the server by using the external SCSI connector on the back of the unit, or by using an optional WideUltra SCSI-3 Controller board. To install an external storage device to the external SCSI connector, refer to the installation documentation that came with the external storage device. Also, see Chapter 4, "SCSI Cabling Instructions for Mass Storage SCSI Devices," for additional cabling information. The following illustration provides only an overview of this installation. timber-23 .EPS Figure 3-19. Connecting external mass storage device Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
3-23
Compaq ProLiant 800 Servers Supporting Pentium II Processors and 100-MHz System Bus Setup and Installation
Guide
Installing External Storage
Devices
Optional mass storage devices can be connected to the server by using the
external SCSI connector on the back of the unit, or by using an optional Wide-
Ultra SCSI-3 Controller board. To install an external storage device to the
external SCSI connector, refer to the installation documentation that came
with the external storage device. Also, see Chapter 4, “SCSI Cabling
Instructions for Mass Storage SCSI Devices,” for additional cabling
information. The following illustration provides only an overview of this
installation.
timber-23 .EPS
Figure 3-19. Connecting external mass storage device